Capacidade de óleoConfiança alta
Quantos litros de óleo vão na BMW C 650 GT 2013 a 2015?
A ficha técnica indica 3.1 L com troca do filtro.
Fonte: BMW — documentação técnicaVer detalhe →
BMW C 650 GT 2013 a 2015
Ficha técnica da BMW C 650 GT 2013 a 2015, aplicação 2013 a 2015 com 15 especificações, 158 torques publicados. Consulte os dados disponíveis para esta geração e confirme ano, versão e mercado antes de qualquer serviço.
⚙️
Cilindrada647 cm³⚙️
Potência máxima44 kW🛢️
Óleo com troca do filtro3.1 L📐
Taxa de compressão11.6:1•
Torque máximo66 Nm⛽
Capacidade do tanque16 L💨
Calibragem dianteira2.4 bar💨
Calibragem traseira2.5 bar⚡ Respostas técnicas confirmadas
Atalhos objetivos montados somente com dados publicados de confiança alta ou com origem técnica rastreável nesta geração.
CalibragemConfiança alta
Qual a calibragem dos pneus da BMW C 650 GT 2013 a 2015?
Pressões publicadas: dianteiro 2.4 bar; traseiro 2.5 bar.
Fonte: BMW — documentação técnicaVer detalhe →
Peso-potênciaConfiança alta
Qual a relação peso-potência da BMW C 650 GT 2013 a 2015?
Com os valores rastreáveis desta ficha, a relação calculada é 4,36 kg/cv.
Fonte: BMW — documentação técnicaVer detalhe →
TanqueConfiança alta
Qual a capacidade do tanque da BMW C 650 GT 2013 a 2015?
A capacidade publicada é 16 L.
Fonte: BMW — documentação técnicaVer detalhe →
Torque de apertoConfiança alta
Qual o torque de Install screw (1) with new sealing ring (2). na BMW C 650 GT 2013 a 2015?
O torque publicado é 10,0 N·m.
Fonte: BMW — documentação técnicaVer detalhe →
🏍️ Visão geral
Valores vinculados ao modelo e à faixa de anos desta ficha.
Altura do assentoFonte técnica: BMW — documentação técnica805 mm
Velocidade máximaFonte técnica: BMW — documentação técnica175 km/h
Reserva de combustívelFonte técnica: BMW — documentação técnica3 L
📐 Dimensões, pesos e capacidades
Valores vinculados ao modelo e à faixa de anos desta ficha.
Peso em ordem de marchaFonte técnica: BMW — documentação técnica261 kg
⚙️ Motor, óleo e regulagens
Valores vinculados ao modelo e à faixa de anos desta ficha.
CilindradaFonte técnica: BMW — documentação técnica647 cm³
Potência máximaFonte técnica: BMW — documentação técnica44 kW
Óleo com troca do filtroFonte técnica: BMW — documentação técnica3.1 L
Taxa de compressãoFonte técnica: BMW — documentação técnica11.6:1
Torque máximoFonte técnica: BMW — documentação técnica66 Nm
Diâmetro do cilindroFonte técnica: BMW — documentação técnica79 mm
Curso do pistãoFonte técnica: BMW — documentação técnica66 mm
⛽ Combustível e alimentação
Valores vinculados ao modelo e à faixa de anos desta ficha.
Capacidade do tanqueFonte técnica: BMW — documentação técnica16 L
⭕ Pneus e calibragem
Valores vinculados ao modelo e à faixa de anos desta ficha.
Calibragem dianteiraFonte técnica: BMW — documentação técnica2.4 bar
Calibragem traseiraFonte técnica: BMW — documentação técnica2.5 bar
📋 Ignicao
Valores vinculados ao modelo e à faixa de anos desta ficha.
Folga do eletrodo da velaFonte técnica: BMW — documentação técnica0.8 mm
🔧 Torques de aperto
Use ferramenta calibrada e confirme as notas específicas antes do serviço. Total encontrado: 158.
| Sistema | Componente | Torque | Rosca / quantidade | Notas | Fonte |
|---|---|---|---|---|---|
| Motor | engine components can be difficult to separate. Separate the engine | 10,0 N·m | — | Contexto da tabela: components by tapping them with a rubber mallet, without damaging; cooling ribs or other parts of the crankcase.; (-) Securing right crankcase cover; Clean all sealing faces.; Apply sealant thinly to the sealing face.; NOTICE; Exercise particularly meticulous care when sealing areas where two; sealing faces/joins meet.; Sealant; Dow Corning 07 58 0 397 777; If applicable, align pump shaft (1) with driver (2).; Carefully place cover (3) with screws (4) in position.; Install screws (5).; Install screw (7) with new sealing ring (8).; Tighten screws (4) to (7) in diagonally opposite sequence.; Crankcase cover, right, to crankcase | · p. PDF 83 |
| Motor | Install screws (1) and tighten until hand-tight. | 3,0 N·m | — | Contexto da tabela: Tighten the screws in the sequence indicated (1) to (18).; earing frame to crankcase (main bearing); M9 x 1.25 1st step:; lubricate with engine oil 1st tightening | · p. PDF 100 |
| Motor | (-) Removing locator for TDC position | 20,0 N·m | — | Contexto da tabela: Remove locking pin (No. 11 0 841) from the hole (arrow) in crankshaft; (3).; Install new seal (2) and screw (1).; Threaded plug (hole for locking pin) to engine cover, right | · p. PDF 114 |
| Motor | Result: | 20,0 N·m | — | Contexto da tabela: Marks are not correct.; Measure:; Install camshafts correctly.; (-) Installing threaded plug (crankshaft); Check sealing ring (1); replace if necessary.; Install screw (2) with sealing ring (1).; Threaded plug (crankshaft) to engine cover, right | · p. PDF 115 |
| Motor | opposite sequence. | 10,0 N·m | — | Contexto da tabela: Tighten screws (1) and (2) uniformly and step by step in diagonally; opposite sequence.; Camshaft bearing cap to cylinder head | · p. PDF 122 |
| Motor | Continue turning the engine until the right cylinder is at firing TDC | 20,0 N·m | — | Contexto da tabela: (both valves are closed).; Mark on crankshaft (dot) is toward line mark II.; Check valve clearance in the same way and note down the figure.; Technical data; Inlet valve ngine 0.04 0.20 mm; clearance coldCmax 35 0.04; xhaust valve ngine 0.04 0.28 mm; clearance coldCmax 35 0.04; Result:; Valve clearance out of tolerance; Measure:; (Billed as a separate item); (-) Installing threaded plug (crankshaft); Check sealing ring (1); replace if necessary.; Install screw (2) with sealing ring (1).; Threaded plug (crankshaft) to engine cover, right | · p. PDF 124 |
| Motor | (-) Installing threaded plug (crankshaft) | 20,0 N·m | — | Contexto da tabela: Check sealing ring (1); replace if necessary.; Install screw (2) with sealing ring (1).; Threaded plug (crankshaft) to engine cover, right | · p. PDF 139 |
| Motor | Technical data | 9,0 N·m | — | Contexto da tabela: Inlet valve ngine 0.04 0.20 mm; clearance coldCmax 35 0.04; xhaust valve ngine 0.04 0.28 mm; clearance coldCmax 35 0.04; (-) Installing screw for timing-chain tensioner; Install screw (1) with seal (2).; Threaded plug in chain tensioner | · p. PDF 139 |
| Motor | (-) Installing air intake stub | 10,0 N·m | — | Contexto da tabela: Remove the cloth from the intake ducts (arrows).; Check seal (4); replace if necessary.; Hold air intake stub (3) in position and secure it with screws (2).; Air intake to cylinder head | · p. PDF 142 |
| Motor | Install spark plugs (1) with spark-plug wrench (No. 12 1 220). | 12,0 N·m | — | Contexto da tabela: Spark plug to cylinder head | · p. PDF 152 |
| Motor | Requirement | 150,0 N·m | — | Contexto da tabela: Engine locked.; Insert screw (No. 11 0 831) (Order No. 83 30 2 297 981) into puller; (No. 12 5 510).; Remove screw (1) and washer (2).; Remove magnetic wheel (3) with puller (No. 12 5 510).; (-) Installing magnetic wheel; Requirement; Engine locked.; Carefully clean the tapers of crankshaft (1) and magnetic wheel (2).; Place magnetic wheel (2), noting the locator (arrows).; Install washer (3) and screw (4); Magnetic gear to crankshaft | · p. PDF 160 |
| Motor | (-) Installing magnetic wheel | 150,0 N·m | — | Contexto da tabela: Requirement; Engine locked.; Carefully clean the tapers of crankshaft (1) and magnetic wheel (2).; Place magnetic wheel (2), noting the locator (arrows).; Install washer (3) and screw (4); Magnetic gear to crankshaft | · p. PDF 165 |
| Motor | NOTICE | 10,0 N·m | — | Contexto da tabela: + 12 72 520; NOTICE; Discontinuation of the camshaft sensor with its wiring-harness plug from; model year 2014 onward.; Preparatory work; Removing air deflector; Core activity; (-) Removing camshaft sensor; Disconnect plug (1).; Remove screw (2).; Remove camshaft sensor (3) with seal (4).; (-) Installing camshaft sensor; Install camshaft sensor (3) with new seal (4).; Install screw (2).; Camshaft sensor to cylinder head cover | · p. PDF 178 |
| Motor | Seal off fuel feed hose (3) with hose clamp (No. 13 3 010). | 3,0 N·m | — | Contexto da tabela: Disengage fuel feed hose (3) from injection line (5).; Remove injection line (5) with injection valves (6), noting O-rings (7).; Remove spring clips (4).; Remove injection valves (6) with O-rings (7) from injection line (5).; (-) Installing injection line; Clean the threads.; Replace O-rings (1) and lubricate; Care products; Rubber care product 83 12 0 397 018; Secure injection valves (2) with spring clips (3) in new injection line (4),; noting O-rings (1).; Insert injection line (4), noting O-rings (1).; Install screws (5).; Injection rail to adapter for throttle valve | · p. PDF 180 |
| Motor | software) | 6,0 N·m | — | Contexto da tabela: NOTICE; Before removal, test the control unit with the BMW Motorrad diagnostic; system and make a backup copy of the data.; Preparatory work; Removing top left fairing side panel; Core activity; (-) Remove the control unit; Open the cable tie (arrow).; Remove screws (1).; Disengage control unit (2) and disconnect plug (3).; (-) Installing control unit; Connect plug (3).; Secure control unit (2) with screws (1).; Control unit to bracket | · p. PDF 188 |
| Motor | Connect the BMW Motorrad battery charger to the battery. | 4,0 N·m | — | Contexto da tabela: NOTICE; When carrying out diagnosis and programming, use a battery charger; with 30 A approved by BMW Motorrad that ensures an on-board; system voltage of 13 V.; Disengage diagnosis plug (1) from the holder (arrow) and remove; protective cap (2).; Connect diagnosis plug (1) to the BMW Motorrad diagnostic system.; NOTICE; See the information about the BMW Motorrad diagnostic system for all; further instructions.; Open the Service functions program.; Run the "Adjust throttle-valve sensor" service program.; Turn potentiometer (1) until the value is OK.; Tighten screw (2).; Throttle-valve switch (potentiometer) to throttle-valve stub | · p. PDF 192 |
| Motor | Care products | 3,0 N·m | — | Contexto da tabela: Rubber care product 83 12 0 397 018; Install injection valve (6) in injection rail (5), noting O-ring (6).; Install spring clip (4).; Insert injection rail (5).; Install screws (2).; Injection rail to adapter for throttle valve | · p. PDF 196 |
| Motor | Disengage sensor housing (2). | 14,0 N·m | — | Contexto da tabela: Remove nuts (1) and disengage exhaust manifold (2).; Remove exhaust manifold (2) and gaskets (3); if applicable lubricate; retaining pins (4).; Installation tool; Silicone spray 83 19 2 208 609; (-) Installing exhaust manifold; Lubricate retaining pins (5).; Installation tool; Silicone spray 83 19 2 208 609; Install new gaskets (4) and seat exhaust manifold (3) on retaining pins; (5).; Secure exhaust manifold (3) with nuts (2).; Manifold to cylinder head | · p. PDF 231 |
| Motor | encapsulated) | 10,0 N·m | — | Contexto da tabela: Thread-locking compound (Micro-; encapsulated); or, Thread-locking compound; (Loctite 243, Medium strength); Clean seat of radial shaft seal (1).; NOTICE; The outside of the shaft sealing ring must be dry on installation; if; necessary clean the seat in the housing.; Lightly lubricate only the sealing lip of radial shaft seal (1) with engine; oil, all other surfaces must be dry and free of grease on installation.; Insert sliding sleeve (No. 11 0 881) and new radial shaft seal (1).; Screw on assembly tool (No. 11 0 881) with thrust nut (No. 11 0 883); until seated; in this process counter-hold at the hexagon (arrow) to; prevent the mandrel from turning.; Remove the tools.; (-) Installing oil line to CVT input shaft; Insert oil line (3) with new sealing ring (4).; Install screws (1) and (2).; Oil line (CVT input shaft) to engine | · p. PDF 282 |
| Motor | Install boot (3). | 15,0 N·m | — | Contexto da tabela: Lubricate fixed fork tube (1) with Fork oil and insert into slider tube (2).; Install boot (3).; Pouring oil into left fork leg; Pour in the correct quantity of oil.; Technical data; Fork oil, capacity 390 ml; per fork leg; Telescopic fork oil (Telescopic fork oil SAE 7.5); Compress and extend the piston rod a few times to make sure that the; damper is completely filled.; Check sealing ring (1); replace if necessary.; Move locknut (2) on rod (3) all the way down, install cover (4).; Secure cover (4) with locknut (2).; Locknut to cover | · p. PDF 328 |
| Motor | Insert adjusting tool (D) (No. 33 6 782) into the removed left frame | 56,0 N·m | — | Contexto da tabela: side section (1).; Insert adjusting tool (A) (No. 33 6 785) into gearbox shaft (1) and; preload.; Hold left frame side section (2) in position with tools (B), (C) and (D); installed.; Insert adjusting tools (E ) and (F ) (No. 33 6 783) into right frame side; section (1) and preload.; Insert shaft (D) until seated.; Insert screws (1) into centre stand (2).; Install screws (5).; Secure right frame side section (6) with nuts (3) and (4).; rame side section to engine; M10 x 230, Screw | · p. PDF 352 |
| Motor | Install screws (1) with washers (2). | 38,0 N·m | — | Contexto da tabela: Engine to frame | · p. PDF 465 |
| Motor | Remove screws (1) and washers (2). | 38,0 N·m | — | Contexto da tabela: Carefully remove frame (3).; (-) Installing main frame; ATTENTION; Incorrect routing of hoses, cables and Bowden cables.; Malfunction. Component damage.; Make sure that routing is correct.; Consult the function diagrams and overviews.; Carefully manoeuvre frame (3) into position.; Install screws (1) with washers (2).; Engine to frame | · p. PDF 465 |
| Rodas/Pneus | Construction status: | 8,0 N·m | — | Contexto da tabela: + 12 32 500; Construction status:; February 2014; Preparatory work; Removing top right side panel; Core activity; (-) Removing voltage regulator; Disengage relay carrier (1).; Disconnect plug (1).; Remove screws (2).; ATTENTION; Hard or sharp-edged objects.; Component damage; Take care not to scratch components; cover or mask as necessary.; Remove voltage regulator (3) by working it down, taking care not to; damage the front wheel cover.; (-) Installing voltage regulator; Hold voltage regulator (3) in position.; Voltage regulator to fairing bracket | · p. PDF 168 |
| Rodas/Pneus | Install special tools (No. 34 0 611) in rear-wheel axle, seating the pin | 180,0 N·m | — | Contexto da tabela: against the spoke (arrow).; Turn rear wheel (1) in the forward direction of travel by applying; torque.; Check; Technical data | · p. PDF 430 |
| Rodas/Pneus | Install the following components: | 60,0 N·m | — | Contexto da tabela: Bowden cable (2); Spring (4); Pin (3); Adjusting screw (1); (-) Installing rear wheel; Hold rear wheel (2) in position and install screws (1).; Rear wheel to output shaft; M10 x 1.25 x 40 Tighten in; diagonally; opposite; sequence | · p. PDF 433 |
| Rodas/Pneus | Preparatory work | 2,0 N·m | — | Contexto da tabela: + 46 61 502; Preparatory work; Removing front-wheel cover; Core activity; (-) Removing front section of wheel cover; Remove screws (1).; Remove front section (2), noting the locators (arrows).; (-) Installing front section of wheel cover; Install front section (2), noting the locators (arrows).; Install screws (1).; Wheel cover, front, to wheel cover, rear | · p. PDF 473 |
| Suspensão | Align the gaps of steering stops (1) with screw heads (3). | 8,0 N·m | — | Contexto da tabela: ATTENTION; Component collision due to projecting cable ties.; Restricted clearance of the steering stop.; Cut off the projecting ends of the cable ties flush at the heads.; Alternately tighten cable ties (4) until the edges (arrows) of steering; stops (1) touch and there is no longer a visible gap.; Cut off the ends of cable ties (3).; (-) Securing screws (brake line to fork bridge) with thread-; locking compound; Clean screws (1) and apply thread-locking compound.; Thread-locking compound; Loctite 270, High strength 83 19 2 210 337; Insert screws (1) by hand.; Tighten screws (1), working from above through the hole (arrow).; Brake line to bottom fork bridge | · p. PDF 24 |
| Suspensão | Fork leg to bottom fork bridge | 19,0 N·m | — | Contexto da tabela: M8 x 25 Tighten screws; six times in; alternate; sequence | · p. PDF 319 |
| Suspensão | Fork leg to top fork bridge | 19,0 N·m | — | Contexto da tabela: Tighten screws (1) and (2).; Fork leg to top fork bridge | · p. PDF 323 |
| Suspensão | Swing the forks 3x | 20,0 N·m | — | Contexto da tabela: to left/right through; full arc of travel; Loosen, 60°; (forks turned fully to | · p. PDF 324 |
| Suspensão | Fork bridge, top, to adjusting screw (steering-head adjustment) | 19,0 N·m | — | — | · p. PDF 325 |
| Suspensão | Seat fork leg (1) in mount (No. 31 3 715). | 15,0 N·m | — | Contexto da tabela: Secure fork leg (1) with rubber retainer (A) in pretensioning tool (No.; Check sealing ring (1); replace if necessary.; Operate hold-down tool (B) of pretensioning tool (No. 31 3 712) until; locknut (1) is accessible.; Screw fork cap (2) on all the way.; Locate locknut (1) with an open-ended spanner and tighten fork cap; (2).; Locknut to cover | · p. PDF 334 |
| Suspensão | Install bearing cap (1). | 19,0 N·m | — | Contexto da tabela: Tighten screws (1).; Swinging arm, right, to swinging-arm shaft | · p. PDF 355 |
| Suspensão | Push the swinging arm all the way to the left and tighten screw (2). | 38,0 N·m | — | Contexto da tabela: Swinging arm, left, to threaded bush | · p. PDF 355 |
| Suspensão | Install left bearing cap (1). | 19,0 N·m | — | Contexto da tabela: Tighten screws (1).; Swinging arm, right, to swinging-arm shaft | · p. PDF 360 |
| Suspensão | (shoulder to the inside). | 12,0 N·m | — | Contexto da tabela: Place swinging-arm housing cover (3) in position with a new gasket; (2).; Install sealing washers (4) and screws (5), noting Bowden-cable holder; (6).; Swinging-arm housing cover to rear wheel swinging arm; M6 x 30 tighten in; diagonally; opposite; sequence | · p. PDF 363 |
| Suspensão | Preparatory work | 66,0 N·m | — | Contexto da tabela: + 33 54 500; Preparatory work; Removing filler cap flap; Opening seat; Removing centre cover; Removing top left fairing side panel; Removing front left footplate insert and footrest plate; Removing bottom left fairing panel; Removing left side panel; Removing centre left footplate insert and footrest plate; Removing rear left footplate insert and footrest plate; Removing left footplate; Core activity; (-) Removing spring strut; Support the rear wheel with wedges (No. 36 5 521).; Remove screws (1) and remove spring strut (2).; (-) Installing spring strut; Insert spring strut (2) and install screws (1).; Spring strut to frame and swinging arm | · p. PDF 364 |
| Suspensão | From behind, position washer (No. 33 2 534) on swinging arm (2) and | 66,0 N·m | — | Contexto da tabela: install spindle with thrust nut (No. 33 2 531).; B mark (arrow) to swinging arm (2); Install suitable washer (3) and nut (4) and tighten until hand-tight.; Pull spring-strut swivel bearing (1) into swinging arm (2) until seated.; (-) Installing spring strut; Insert spring strut (2) and install screws (1).; Spring strut to frame and swinging arm | · p. PDF 367 |
| Suspensão | Install bearing cap (2). | 66,0 N·m | — | Contexto da tabela: (-) Installing spring strut; Insert spring strut (2) and install screws (1).; pring strut to frame and swinging arm | · p. PDF 379 |
| Suspensão | ATTENTION | 28,0 N·m | — | Contexto da tabela: Brake fluid on painted surfaces, plastic and rubber components.; Material damage; Do not allow brake fluid to come into contact with painted surfaces,; plastic or rubber components.; Hold brake caliper (5) in position and install screws (4).; Brake caliper, rear, to rear wheel swinging arm | · p. PDF 425 |
| Suspensão | Place parking brake (5) in position and install screws (4) in the same | 30,0 N·m | — | Contexto da tabela: way.; Brake caliper (parking brake) to swinging arm | · p. PDF 441 |
| Suspensão | Core activity | 5,0 N·m | — | Contexto da tabela: + 46 61 500; Core activity; (-) Removing front-wheel cover; Remove screws (1) and remove wheel cover (2).; (-) Installing front-wheel cover; Hold wheel cover (2) in position and install screws (1).; Wheel cover to forks | · p. PDF 472 |
| Suspensão | Remove screws (1) and (2). | 19,0 N·m | — | Contexto da tabela: ATTENTION; Hard or sharp-edged components.; Scratches and damage to paintwork.; Use a suitable soft cover or mask off the areas at risk.; Work fairing bracket (3) clear, noting both fork legs (arrows).; Remove fairing bracket (3).; (-) Securing fairing bracket to frame; Requirement; Handlebars turned to the left.; ATTENTION; Hard or sharp-edged components.; Scratches and damage to paintwork.; Use a suitable soft cover or mask off the areas at risk.; Work fairing bracket (3) into position, noting both fork legs (arrows).; Install screws (2) and (1).; Front panel carrier to frame | · p. PDF 499 |
| Transmissão final | (-) Removing timing-chain tensioner | 10,0 N·m | — | Contexto da tabela: Disengage the cable holder (arrow).; Remove screws (1), taking care to slacken them uniformly to prevent; the component from tilting.; Remove timing-chain tensioner (2) and gasket (3).; (-) Install the new timing-chain tensioner; Clean the sealing faces.; Position timing-chain tensioner (2) with a new gasket (3).; Install screws (1), taking care to tighten them uniformly to prevent; the component from tilting.; Chain tensioner in crankcase | · p. PDF 32 |
| Transmissão final | (-) Installing CVT input shaft | 150,0 N·m | — | Contexto da tabela: Install drive shaft (1), noting judder damper (2).; Clean the threads.; Install washer (3).; ATTENTION; Shelf life of micro-encapsulated screws overshot.; Insufficient securing effect.; Use additional thread locking.; Install nut (4), counter-holding at hexagon of drive shaft (1).; CVT input shaft to crankcase | · p. PDF 52 |
| Transmissão final | (-) Securing timing-chain rail | 10,0 N·m | — | Contexto da tabela: Secure timing-chain rail (2) with screw (1).; Chain slide rail to crankcase | · p. PDF 63 |
| Transmissão final | Chain slide rail to crankcase | 10,0 N·m | — | — | · p. PDF 118 |
| Transmissão final | Timing-chain tensioner (2) turns to the working position. | 9,0 N·m | — | Contexto da tabela: Remove pretensioning tool (No. 11 0 842).; Secure the cable (arrow).; (-) Installing screw for timing-chain tensioner; Install screw (1) with seal (2).; Threaded plug in chain tensioner | · p. PDF 125 |
| Transmissão final | Preparatory work | 10,0 N·m | — | Contexto da tabela: Removing chain guide; Core activity; (-) Removing oil pump; Remove screws (1).; Remove oil pump (2), noting sealing ring (3).; (-) Installing oil pump; Install sealing ring (1).; Hold oil pump (2) in position, noting gearwheels (3).; Install screws (4).; Oil pump to bearing frame | · p. PDF 140 |
| Transmissão final | Use additional thread locking. | 150,0 N·m | — | Contexto da tabela: Install nut (4), counter-holding at hexagon of drive shaft (1).; CVT input shaft to crankcase | · p. PDF 282 |
| Transmissão final | Install new sealing ring (1) in front pinion cover (2) (open side toward | 4,5 N·m | — | Contexto da tabela: the inside).; Clean the sealing face and seal, taking particular care at the corners; (arrows).; NOTICE; When using fluids and lubricants, always comply with specifications such; as flash time or drying time.; See the data sheets/product information publications for more details.; Sealant; Dow Corning 07 58 0 397 777; Clean the sealing face.; Install new square-section sealing ring (1) on rear pinion cover (2).; Install front pinion cover (3).; Work rear pinion cover (2) over the chain.; Install screws (1), noting the tightening sequence.; Pinion cover, front section to rear section; M5 x 16 Tightening; sequence: 1st: top; (from front), 2nd; bottom (from; behind) | · p. PDF 350 |
| Transmissão final | Check | 5,0 N·m | — | Contexto da tabela: Result:; Pin head not adequately secured.; Measure:; Repeat the process step and seat the pin head more securely.; Check; Result:; Pin head cracked, irregularly flattened or rounded.; Measure:; Remove the chain joining link and again install a new chain oining; link.; (-) Installing pinion and chain; Install new pinion (4), lettering toward the outside.; Seat retainer (3) in the key seat (arrow).; Turn retainer (3) until screws (2) can be installed.; Install screws (2).; Retaining plate to pinion | · p. PDF 373 |
| Transmissão final | as flash time or drying time. | 4,5 N·m | — | Contexto da tabela: See the data sheets/product information publications for more details.; ealant; Dow Corning 07 58 0 397 777; Clean the sealing face.; Install new square-section sealing ring (1) on rear pinion cover (2).; Install front pinion cover (3).; Work rear pinion cover (2) over the chain.; Install screws (1), noting the tightening sequence.; Pinion cover, front section to rear section; M5 16 Tightening; sequence: 1st: top; (from front), nd; bottom (from; behind) | · p. PDF 374 |
| Transmissão final | (-) Installing sprocket and output shaft | 8,0 N·m | — | Contexto da tabela: Insert sprocket (3) into chain (4).; Insert output shaft (2) into sprocket (3).; Clean the threads and install new nut (1) and tighten until hand-tight.; Secure retaining plate (2) with screws (1).; Retaining plate for grooved ball bearing to rear wheel swinging; arm | · p. PDF 380 |
| Transmissão final | Measure: | 8,0 N·m | — | Contexto da tabela: Replace the chain sprocket, chain pinion and chain.; => 33 81 500, Replacing chainset (Billed as a separate item); Result:; Fig. 3: Severe wear at the teeth is perceptible.; Measure:; Replace the chain sprocket, chain pinion and chain.; => 33 81 500, Replacing chainset (Billed as a separate item); (-) Installing chain tensioner rail (oversize); To adjust chain sag, select the next largest chain tensioner rail; (number of dots).; Chain tensioner rails are available in 4 stages; the number of dots; (arrow) corresponds to the stage.; Clean the threads.; Transfer sleeve (4) to the new part.; Insert oversize chain tensioner rail (3).; Install screws (1) and (2).; Chain tensioner rail to rear wheel swinging arm | · p. PDF 397 |
| Transmissão final | (-) Remove the chain slide rail | 8,0 N·m | — | Contexto da tabela: Remove screws (1) and (2).; Remove chain slide rail (3).; (-) Installing chain slide rail; Clean the threads.; Work chain slide rail (1) into position, noting the locator (arrow).; Secure chain slide rail (3) with screws (1) and (2).; Chain slide rail to rear wheel swinging arm | · p. PDF 405 |
| Transmissão final | (-) Installing top chain channel | 8,0 N·m | — | Contexto da tabela: Secure chain channel (1) in the holders (arrows).; Install screw (2).; (-) Installing chain tensioner rail; Clean the threads.; Insert chain tensioner rail (3), noting sleeve (4).; Install screws (1) and (2).; Chain tensioner rail to rear wheel swinging arm | · p. PDF 406 |
❓ Perguntas frequentes
As respostas abaixo são montadas somente com dados publicados nesta ficha.
Quantos litros de óleo vão na BMW C 650 GT 2013 a 2015?
A ficha técnica indica: 3.1 L com troca do filtro.
Qual é a taxa de compressão da BMW C 650 GT 2013 a 2015?
A ficha técnica indica: 11.6:1.
Qual é a calibragem dos pneus da BMW C 650 GT 2013 a 2015?
A ficha técnica indica: dianteiro: 2.4 bar; traseiro: 2.5 bar.
Qual é a capacidade do tanque da BMW C 650 GT 2013 a 2015?
A ficha técnica indica: 16 L.
Quais são o diâmetro e o curso do motor da BMW C 650 GT 2013 a 2015?
A ficha técnica indica: 79 mm × 66 mm.
Qual é o torque de Install screw (1) with new sealing ring (2). na BMW C 650 GT 2013 a 2015?
10,0 N·m — Contexto da tabela: Drain plug to coolant pump.
Qual é o torque de Preparatory work na BMW C 650 GT 2013 a 2015?
2,0 N·m — Contexto da tabela: + 17 40 500; Preparatory work; Removing filler cap flap; Opening seat; Removing top right side panel; Removing front right footplate insert and footrest plate; Removing bottom right fairing panel; Removing centre right footplate insert and footrest plate; Removing rear right footplate insert and footrest plate; Removing centre cover; Removing right side panel; Removing rear footplate; Removing air deflector; Disengaging and lowering radiator; Core activity; (-) Removing fan; Push radiator (1) forward and remove nuts (2) with washers (3).; Remove fan (4).; (-) Installing fan; Position fan (4) on radiator (1).; Install washers (3) and nuts (2).; Radiator cowl to radiator; M4 x 35, Screw.