Capacidade de óleoConfiança alta
Quantos litros de óleo vão na BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica 3.0 L com troca do filtro.
Fonte: BMW — documentação técnicaVer detalhe →
BMW F 850 GS Adventure K82 2018 a 2021
Dados técnicos, manutenção e torques da BMW F 850 GS Adventure K82, anos 2018 a 2021, com fontes por página.
⚙️
Cilindrada853 cm³📐
Taxa de compressão13.1:1•
Torque máximo92 Nm⚙️
Potência máxima70 kW (95 cv) a 8.250 rpm🛢️
Óleo com troca do filtro3.0 L🔧
Torque máximo92 N·m a 6.250 rpm📏
Folga de válvula — admissão0.11...0.20 mm📏
Folga de válvula - escape0.30...0.35 mm⛽
Capacidade do tanque23 L⚙️
Câmbio6 marchas, engrenagens de engate constante integradas ao motor⚡ Respostas técnicas confirmadas
Atalhos objetivos montados somente com dados publicados de confiança alta ou com origem técnica rastreável nesta geração.
PneusConfiança alta
Quais pneus usa a BMW F 850 GS Adventure K82 2018 a 2021?
Medidas publicadas: dianteiro 90/90-21; traseiro 150/70 R17.
Fonte: BMW — documentação técnicaVer detalhe →
CalibragemConfiança alta
Qual a calibragem dos pneus da BMW F 850 GS Adventure K82 2018 a 2021?
Pressões publicadas: dianteiro 2.2 bar; traseiro 2.5 bar.
Fonte: BMW — documentação técnicaVer detalhe →
Folga de válvulasConfiança alta
Qual a folga de válvulas da BMW F 850 GS Adventure K82 2018 a 2021?
Valores publicados: admissão 0.11...0.20 mm; escape 0.30...0.35 mm.
Fonte: BMW — documentação técnicaVer detalhe →
Peso-potênciaConfiança alta
Qual a relação peso-potência da BMW F 850 GS Adventure K82 2018 a 2021?
Com os valores rastreáveis desta ficha, a relação calculada é 2,56 kg/cv.
Fonte: BMW — documentação técnicaVer detalhe →
TanqueConfiança alta
Qual a capacidade do tanque da BMW F 850 GS Adventure K82 2018 a 2021?
A capacidade publicada é 23 L.
Fonte: BMW — documentação técnicaVer detalhe →
Torque de apertoConfiança alta
Qual o torque de Coolant drain plug to water pump na BMW F 850 GS Adventure K82 2018 a 2021?
O torque publicado é 6,0 N·m.
Fonte: BMW — documentação técnicaVer detalhe →
🏍️ Visão geral
Valores vinculados ao modelo e à faixa de anos desta ficha.
Distância entre eixosFonte técnica: BMW — documentação técnica1.593 mm
Altura do assentoFonte técnica: BMW — documentação técnica875 mm
📐 Dimensões, pesos e capacidades
Valores vinculados ao modelo e à faixa de anos desta ficha.
ComprimentoFonte técnica: BMW — documentação técnica2.300 mm
Largura com retrovisoresFonte técnica: BMW — documentação técnica939 mm
Peso em ordem de marcha (DIN)Fonte técnica: BMW — documentação técnica244 kg
Peso total permitidoFonte técnica: BMW — documentação técnica455 kg
⚙️ Motor, óleo e regulagens
Valores vinculados ao modelo e à faixa de anos desta ficha.
CilindradaFonte técnica: BMW — documentação técnica853 cm³
Taxa de compressãoFonte técnica: BMW — documentação técnica13.1:1
Torque máximoFonte técnica: BMW — documentação técnica92 Nm
Potência máximaFonte técnica: BMW — documentação técnica70 kW (95 cv) a 8.250 rpm
Diâmetro do cilindroFonte técnica: BMW — documentação técnica84 mm
Óleo com troca do filtroFonte técnica: BMW — documentação técnica3.0 L
Torque máximoFonte técnica: BMW — documentação técnica92 N·m a 6.250 rpm
Curso do pistãoFonte técnica: BMW — documentação técnica77 mm
Tipo de motorFonte técnica: BMW — documentação técnicaBicilíndrico em linha, 4 tempos, quatro válvulas por cilindro e dois comandos no cabeçote
ArrefecimentoFonte técnica: BMW — documentação técnicaLíquido
Folga de válvula — admissãoFonte técnica: BMW — documentação técnica0.11...0.20 mm
Folga de válvula - escapeFonte técnica: BMW — documentação técnica0.30...0.35 mm
⛽ Combustível e alimentação
Valores vinculados ao modelo e à faixa de anos desta ficha.
Capacidade do tanqueFonte técnica: BMW — documentação técnica23 L
⛓️ Transmissão, embreagem e relação
Valores vinculados ao modelo e à faixa de anos desta ficha.
EmbreagemFonte técnica: BMW — documentação técnicaMultidisco em banho de óleo, assistida e antideslizante, acionamento mecânico
CâmbioFonte técnica: BMW — documentação técnica6 marchas, engrenagens de engate constante integradas ao motor
Folga da correnteFonte técnica: BMW — documentação técnica40...50 mm
Relação primáriaFonte técnica: BMW — documentação técnica1,821
Relações do câmbioFonte técnica: BMW — documentação técnica1ª 2,833; 2ª 2,067; 3ª 1,600; 4ª 1,308; 5ª 1,103; 6ª 0,968
Transmissão finalFonte técnica: BMW — documentação técnicaCorrente O-Ring sem emenda, com amortecedor de torção no cubo traseiro
Relação finalFonte técnica: BMW — documentação técnica2,588
⭕ Pneus e calibragem
Valores vinculados ao modelo e à faixa de anos desta ficha.
Calibragem dianteiraFonte técnica: BMW — documentação técnica2.2 bar
Calibragem traseiraFonte técnica: BMW — documentação técnica2.5 bar
Pneu dianteiroFonte técnica: BMW — documentação técnica90/90-21
Pneu traseiroFonte técnica: BMW — documentação técnica150/70 R17
↕️ Suspensão
Valores vinculados ao modelo e à faixa de anos desta ficha.
Óleo da bengala esquerdaFonte técnica: BMW — documentação técnica660 ml
Óleo da bengala direitaFonte técnica: BMW — documentação técnica557 ml
Suspensão dianteiraFonte técnica: BMW — documentação técnicaGarfo invertido de 43 mm
Suspensão traseiraFonte técnica: BMW — documentação técnicaBalança de alumínio com monoamortecedor, pré-carga hidráulica e retorno ajustável
Curso da suspensão dianteiraFonte técnica: BMW — documentação técnica230 mm
Curso da suspensão traseiraFonte técnica: BMW — documentação técnica215 mm
🛑 Freios
Valores vinculados ao modelo e à faixa de anos desta ficha.
Freio dianteiroFonte técnica: BMW — documentação técnicaDois discos de 305 mm, pinças flutuantes de 2 pistões
Freio traseiroFonte técnica: BMW — documentação técnicaDisco de 265 mm, pinça flutuante de 1 pistão
Diâmetro do freio dianteiroFonte técnica: BMW — documentação técnica2 × 305 mm
Diâmetro do freio traseiroFonte técnica: BMW — documentação técnica265 mm
⚡ Elétrica e ignição
Valores vinculados ao modelo e à faixa de anos desta ficha.
AlternadorFonte técnica: BMW — documentação técnica416 W
Tensão da bateriaFonte técnica: BMW — documentação técnica12 V
Capacidade da bateriaFonte técnica: BMW — documentação técnica10 Ah
📋 Alimentacao
Valores vinculados ao modelo e à faixa de anos desta ficha.
AlimentaçãoFonte técnica: BMW — documentação técnicaInjeção no coletor com gerenciamento eletrônico BMS-M
📋 Chassi
Valores vinculados ao modelo e à faixa de anos desta ficha.
QuadroFonte técnica: BMW — documentação técnicaPonte de aço em construção monocoque, motor como elemento estrutural
Ângulo da coluna de direçãoFonte técnica: BMW — documentação técnica62°
📋 Consumo
Valores vinculados ao modelo e à faixa de anos desta ficha.
Consumo WMTCFonte técnica: BMW — documentação técnica4,1 L/100 km
📋 Desempenho
Valores vinculados ao modelo e à faixa de anos desta ficha.
Velocidade máximaFonte técnica: BMW — documentação técnica197 km/h
🔧 Torques de aperto
Use ferramenta calibrada e confirme as notas específicas antes do serviço. Total encontrado: 375.
| Sistema | Componente | Torque | Rosca / quantidade | Notas | Fonte |
|---|---|---|---|---|---|
| Ignição/Elétrica | Front oxygen sensor to exhaust manifold | 45,0 N·m | — | — | · p. PDF 236 |
| Ignição/Elétrica | Install oxygen sensor (3). | 25,0 N·m | — | Contexto da tabela: Monitoring oxygen sensor to exhaust manifold | · p. PDF 238 |
| Ignição/Elétrica | (-) Replacing fuel tank | 5,0 N·m | — | Contexto da tabela: Remount small parts on new fuel tank (1), if necessary replace with new; parts.; 2 x flat nut, M5; 2 x bushing; 2 x rubber mount; 2 x spacer buffer; 8 x seal; Clean the surfaces for adhesion.; NOTICE; Faces that will be in contact with the adhesive must be dry, clean and free; from dust and grease.; Fix new thermal protection (2) on the inside of new fuel tank (1).; (-) Installing fuel-pump unit; Check seal (1), change if necessary.; Lightly lubricate seal (1) and position it on fuel-pump unit (2).; Installation tool; Silicone spray 83 19 2 208 609; Feed in fuel-pump unit (2) with seal (1) carefully in fuel tank (3), checking; lever sensor (4) and fuel strainer (5) in particular.; NOTICE; Bridge on fuel-pump unit must be in the opposite direction of travel.; Position fuel-pump unit (2) with bridge (arrow) as shown.; Hold pressure plate (1) in position and align with r | · p. PDF 306 |
| Ignição/Elétrica | Check seal (1), change if necessary. | 5,0 N·m | — | Contexto da tabela: Lightly lubricate seal (1) and position it on fuel-pump unit (2).; Installation tool; Silicone spray 83 19 2 208 609; Feed in fuel-pump unit (2) with seal (1) carefully in fuel tank (3), checking; lever sensor (4) and fuel strainer (5) in particular.; NOTICE; Bridge on fuel-pump unit must be in the opposite direction of travel.; Position fuel-pump unit (2) with bridge (arrow) as shown.; Hold pressure plate (1) in position and align with recess (arrow) to bridge of; fuel-pump unit (arrow).; Turn pressure plate (1) and fuel-pump unit (2) slightly, together if necessary,; so that the bore holes for bolts (3) are aligned.; Install bolts (3) and tighten gradually.; Electric fuel pump to fuel tank | · p. PDF 315 |
| Ignição/Elétrica | Release coolant hose (2). | 8,0 N·m | — | Contexto da tabela: Catch coolant in a suitable container.; Release clamp (1) with pliers (No. 17 5 571).; Release breather hose (2).; Remove screws (1).; Remove the radiator (2) with the air duct (3), and release the radiator (2); from the strut (4).; (-) Installing radiator; Fit the radiator (2) with the air ducts (3) and secure in strut (4).; Install screws (1).; Radiator to bracket | · p. PDF 331 |
| Ignição/Elétrica | Silencer to front silencer | 14,0 N·m | — | Contexto da tabela: Tighten nut (1) on the clamp (2).; Silencer to front silencer | · p. PDF 352 |
| Ignição/Elétrica | (mechanical) | 14,0 N·m | — | Contexto da tabela: Thread-locking compound; (mechanical); Tighten nut (1) on the clamp (2).; Front silencer to exhaust manifold | · p. PDF 355 |
| Ignição/Elétrica | Front silencer to exhaust manifold | 14,0 N·m | — | Contexto da tabela: Tighten nut (1) on the clamp (2).; Front silencer to exhaust manifold | · p. PDF 357 |
| Ignição/Elétrica | Carefully turn around the fork leg and empty the oil into a suitable collection | 20,0 N·m | — | Contexto da tabela: container without exposing bore holes (arrows) of slider tube (1).; Clamp fork leg (1) to brake caliper mounting (2) in a vice with vice jaw; protectors.; Remove bolt (3) with sealing ring (4), pressing damper unit (5) to prevent it; from rotating.; Remove damper unit (5) with centering plate (6) and drain damper unit (5); by pumping.; (-) Pouring oil into right fork leg; Clean thread in bottom damper unit (5).; Position damper unit (5) with centering plate (6) in fork leg (1).; Install bolt (3) with a new sealing ring (4).; Damper unit to forkleg | · p. PDF 467 |
| Ignição/Elétrica | Position handlebars (1) with clamping block (2). | 19,0 N·m | — | Contexto da tabela: Align handlebars (1) with the marks (arrows).; WARNING; Incorrect tightening sequence of the handlebar clamps.; Handlebars work loose when vehicle is ridden.; Tighten the handlebar clamps to the specified torque and in the specified; sequence.; Install screws (3).; Handlebar clamping block to fork bridge; M8 x 35 Tightening; sequence: in the; forward direction of; travel, tighten until; seated | · p. PDF 472 |
| Ignição/Elétrica | Installing left mirror | 25,0 N·m | — | Contexto da tabela: Thread-locking compound (Loctite; 243, Medium strength); Installing left mirror; Install complete left/right adapter (2) with mirror (3) and washer (4).; Adapter to clamping block | · p. PDF 474 |
| Ignição/Elétrica | Install brake pads (3) (renew worn brake pads). | 38,0 N·m | — | Contexto da tabela: Serve in locking pin (2) up to limit position and install split-pin keeper (1).; (-) Installing front left brake caliper; Position brake caliper (1) noting the sensor cable (2).; Position retaining plate (3) and install screws (4).; Brake caliper to telescopic fork | · p. PDF 556 |
| Ignição/Elétrica | Route brake hose (1). | 8,0 N·m | — | Contexto da tabela: Close the cable strap (arrows).; Position brake-hose distributor (2).; Install bolt (1).; Brake-hose distributor to fork clamp | · p. PDF 584 |
| Ignição/Elétrica | encapsulated) | 4,6 N·m | — | Contexto da tabela: Thread-locking compound (micro-; encapsulated); Position cable clip(3) in bore hole (Arrow) of brake-caliper support (4) and; install bolt (5).; Cable clip for wheel-speed sensor to brake-caliper support | · p. PDF 612 |
| Ignição/Elétrica | Remove bolt (1). | 8,0 N·m | — | Contexto da tabela: Release wheel speed sensor (2).; Remove bolt (3) and cable clip (4) .; Remove wheel speed sensor (2).; (-) Installing rear wheel-speed sensor; Clean the threads.; Position wheel speed sensor (1) and install bolt (2).; Wheel-speed sensor, rear, to brake caliper carrier | · p. PDF 612 |
| Ignição/Elétrica | Compress the telescopic forks several times to avoid twisting, lower front- | 19,0 N·m | — | Contexto da tabela: wheel stand, if required.; Tighten clamping bolts (1) on left and right.; Clamp of quick-release axle; M8 x 35 Tightening; sequence: Tighten; screws six times in; alternate sequence | · p. PDF 617 |
| Ignição/Elétrica | Lubricant | 50,0 N·m | — | Contexto da tabela: Unirex N3 83 19 2 160 349; ATTENTION; Front wheel installed wrong way round; Risk of accident; Note direction-of-rotation arrows on tyre or rim.; ATTENTION; Installation of front wheel not in compliance with correct procedure; Damage to wheel speed sensor; Note the wheel-speed sensor when rolling in the front wheel.; Position front wheel (3).; Install quick-release axle (2).; Install bolt (1) and tighten, counter-hold the quick-release axle on the right; side with the hexagon head (No. 36 3 691) while doing so.; Axle screw in front quick-release axle | · p. PDF 617 |
| Ignição/Elétrica | (-) Installing front sensor ring | 5,0 N·m | — | Contexto da tabela: Position sensor ring (2).; Install screws (1).; Sensor ring to front wheel | · p. PDF 626 |
| Ignição/Elétrica | Clamp the bearing support (3) with vice jaw protectors in vice. | 41,0 N·m | — | Contexto da tabela: Clean the threads.; Secure side stand (2) with bolt (1).; Side stand to pivot mount | · p. PDF 673 |
| Ignição/Elétrica | Install the mirror (3) and align. | 22,0 N·m | — | Contexto da tabela: Tighten the lock nut (4).; Mirror (locknut) to clamping piece; M10 x 1.25 Left-hand thread, | · p. PDF 722 |
| Ignição/Elétrica | Preparatory work | 8,0 N·m | — | Contexto da tabela: + 51 25 595; Preparatory work; Removing seat; Removing battery; Removing top front-wheel cover; Removing the fuel tank cover; Removing left radiator cowl; Remove fairing side panel with left tank covers; Removing right radiator cowl; Remove fairing side panel with right tank covers; Removing fuel tank; Core activity; (-) Remove the seat lock; Remove screws (1).; Release support (2) and detach from eccentric (3) (swing support arm (4) to; the rear and press spring (5) downwards).; Remove support (2) for seat lock.; (-) Installing seat lock; Position support (2) for the seat lock, attaching it to eccentric (3).; Install screws (1).; Seat retainer bridge to rear frame | · p. PDF 728 |
| Ignição/Elétrica | Core activity | 5,0 N·m | — | Contexto da tabela: (-) Removing battery; Loosen diagnostic connector (1) from holder (2).; Remove screws (3).; Remove the battery holder (4).; Remove the battery (5).; (-) Replacing battery; Remount positive terminal cover (1) to new battery (2).; Dispose of all battery in a manner compliant with national regulations.; (-) Installing battery; Position battery (5).; Install battery holder (4) with screws (3).; Battery holder to rear-wheel cover | · p. PDF 771 |
| Ignição/Elétrica | (-) Replacing rear ride-height sensor | 8,0 N·m | — | Contexto da tabela: Remove nut (1) and ball stud (2).; Clean the threads.; Secure nut (1) and ball stud (2) to ride height sensor (3).; Ball end (actuator rod) to ride-height sensor; Nut, M6 | · p. PDF 778 |
| Ignição/Elétrica | Reuse and secure using Loctite | 4,0 N·m | — | Contexto da tabela: 2701, Thread-locking compound; (micro-encapsulated); (-) Installing height sensor, rear; Hold ride height sensor (2) in position.; Connect connector (1) for the ride height sensor.; Position ride height sensor (2) in holder (3).; Install screws (1).; Ride-height sensor to bracket | · p. PDF 778 |
| Ignição/Elétrica | (-) Assemble sports silencer | 19,0 N·m | — | Contexto da tabela: Lubricate the sports silencer on the inner diameter before connecting the; connecting pipe.; Lubricant; Copper paste 81 22 9 400 794; Connect connecting pipe (1) in sports silencer (3).; Tighten the clamp (2).; Silencer to front silencer | · p. PDF 829 |
| Ignição/Elétrica | Position handlebars high (1) with clamping block (2). | 19,0 N·m | — | Contexto da tabela: Align handlebars high (1) with the marks (arrows).; WARNING; Incorrect tightening sequence of the handlebar clamps.; Handlebars work loose when vehicle is ridden.; Tighten the handlebar clamps to the specified torque and in the specified; sequence.; Install screws (3).; Handlebar clamping block to fork bridge; M8 x 35 Tightening; sequence: in the; forward direction of; travel, tighten until; seated | · p. PDF 839 |
| Ignição/Elétrica | Equipment trim-level variant: | 8,0 N·m | — | Contexto da tabela: + 77 49 507; Equipment trim-level variant:; OA Case holder for aluminium case; Core activity; (-) Fit adapter plate, left; Insert screws (1) with washers (2) in guiding grooves (3) in the adapter; plate.; Position adapter plate (4) on case holder (5).; Position clamping blocks (6) on case holder (5) from the rear and install; screws (1) in clamping blocks (6) until uniformly hand-tight.; Insert screws (1) with long washer (7) in guiding groove (3) in the adapter; plate.; Position long clamping block (8) on case holder (5) from the rear and install; screws (1) in long clamping block (8) until hand-tight.; (-) Tighten adapter plate, left; NOTICE; Before tightening the adapter plate, check if the required height has been; achieved.; Fasten the adapter plate as low as possible due to the centre of gravity of the; vehicle, vehicle height and driving conditions can however | · p. PDF 877 |
| Ignição/Elétrica | NOTICE | 8,0 N·m | — | Contexto da tabela: + 77 51 502; NOTICE; The LED auxiliary headlights have an overheat cutout. The headlights; automatically reduce their brightness if a certain temperature is reached;; under extreme circumstances the headlights can even switch themselves off.; The headlights return to full brightness once they have cooled down; sufficiently.; Preparatory work; Removing seat; Releasing left slipstream deflector; Releasing right slipstream deflector; Core activity; (-) Holder for cable tie to bracket for auxiliary headlight; Install holder (1) for cable strap and holder for plug connector (2) on holder; (3).; (-) Installing bracket for additional LED headlight; Slide up holder (1) for additional LED headlight from the bottom in the; direction of the arrow.; Remove bolts (1) (see magnifying glass).; Attach holder (2) to front panel carrier (3).; Install screws (1). | · p. PDF 880 |
| Ignição/Elétrica | (-) Installing LED auxiliary headlight | 6,0 N·m | — | Contexto da tabela: Position LED additional headlight (1) on holder (2).; Install nuts (3) and bolts (4).; Additional LED headlight to bracket | · p. PDF 881 |
| Ignição/Elétrica | Hold switch for additional LED headlight (1) in position at clamping block (2). | 2,0 N·m | — | Contexto da tabela: Install bolt (3).; Additional switch to clamping block | · p. PDF 882 |
| Ignição/Elétrica | Installing clamping block for manual controls for clutch control | 8,0 N·m | — | Contexto da tabela: Attach clamping block (1) to manual controls (2).; Install screws (3) loosely.; Position manual controls (2) on marks (arrow).; Tighten the screws (3).; Handbrake fitting to handlebars; M6 x 20 Tightening; sequence: tighten; top until fully closed | · p. PDF 882 |
| Ignição/Elétrica | Insert lock barrel (2) with key (1) and turn until locking pawl (arrow) is | 25,0 N·m | — | Contexto da tabela: locked.; Removing screws in left handlebar clamping block; NOTICE; In order to retain the basic setting of the handlebars unchanged, always; slacken only one side of the handlebar clamping block.; Remove screws (1) in left handlebar clamping block.; Installing securing screws in left handlebar clamping block; Clean and lubricate the securing screws.; Lubricant; MP 3 paste 07 55 9 062 476; Screw in bolts (21) and (3) slightly.; Tighten front mounting bolt (2) first.; Tighten rear mounting bolt (3).; Securing screw to handlebar clamping block; M8 x 30 - 10.9 Tightening; sequence: in the Lubricate screw, Lubricant (MP 3; forward direction of paste); travel, tighten until; seated | · p. PDF 898 |
| Ignição/Elétrica | In order to retain the basic setting of the handlebars unchanged, always | 25,0 N·m | — | Contexto da tabela: slacken only one side of the handlebar clamping block.; Remove screws (1) in the right handlebar clamping block.; Installing securing screws in right handlebar clamping block; Clean and lubricate the securing screws.; Lubricant; MP 3 paste 07 55 9 062 476; Slightly screw in screws (2) and (3).; Tighten front mounting bolt (2) first.; Tighten rear mounting bolt (3).; Securing screw to handlebar clamping block; M8 x 30 - 10.9 Tightening; sequence: in the Lubricate screw, Lubricant (MP 3; forward direction of paste); travel, tighten until; seated | · p. PDF 899 |
| Ignição/Elétrica | (-) Installing securing screws in right handlebar clamping block | 25,0 N·m | — | Contexto da tabela: Clean and lubricate the securing screws.; Lubricant; MP 3 paste 07 55 9 062 476; Slightly screw in screws (2) and (3).; Tighten front mounting bolt (2) first.; Tighten rear mounting bolt (3).; Securing screw to handlebar clamping block; M8 x 30 - 10.9 Tightening; sequence: in the Lubricate screw, Lubricant (MP 3; forward direction of paste); travel, tighten until; seated | · p. PDF 907 |
| Ignição/Elétrica | (-) Smartphone Cradle Installation | 1,3 N·m | — | Contexto da tabela: Remove screws (1) and clamping block (2) with transverse axis (3) from; holder (4).; Remove nuts (1) and bolts (2).; Disconnect clamping block upper section (3) and -lower section (4) and; remove transverse axis (5) and keep them safely aside (will be reused).; Position new clamping block lower section (1) and new clamping block; upper section (2) centred at cross-member (3).; Position Smartphone Cradle (4) on the new clamping block upper; section (2).; Install Smartphone Cradle (4) with screws (5).; Smartphone Cradle to bracket | · p. PDF 908 |
| Ignição/Elétrica | other words centred | 50,0 N·m | — | Contexto da tabela: on the rim; Repeat the balancing procedure as a check.; (-) Install the front wheel; Clean and lubricate spacer bush (1), If necessary.; Install spacer bush (1).; Lubricant; Unirex N3 83 19 2 160 349; Clean and lubricate quick-release axle (2).; Lubricant; Unirex N3 83 19 2 160 349; ATTENTION; Front wheel installed wrong way round; Risk of accident; Note direction-of-rotation arrows on tyre or rim.; ATTENTION; Installation of front wheel not in compliance with correct procedure; Damage to wheel speed sensor; Note the wheel-speed sensor when rolling in the front wheel.; Position front wheel (3).; Install quick-release axle (2).; Install bolt (1) and tighten, counter-hold the quick-release axle on the right; side with the hexagon head (No. 36 3 691) while doing so.; Axle screw in front quick-release axle | · p. PDF 924 |
| Ignição/Elétrica | (-) Securing left brake caliper | 38,0 N·m | — | Contexto da tabela: Position brake caliper (1) and holder (2) while noting the sensor cable (3).; Install screws (4).; Brake caliper to telescopic fork | · p. PDF 925 |
| Ignição/Elétrica | (-) Removing chain guard | 3,0 N·m | — | Contexto da tabela: Remove screws (1) from chain guard (3).; Remove expanding rivet (2) in direction (arrow).; (-) Routing supply hose; ATTENTION; Use of unsuitable cleaning and care products; Damage to surfaces; Use a mild solution of soap in water and a soft sponge for cleaning.; Do not use other solvents or fuel.; Clean the surface on rear wheel swinging arm (1).; NOTICE; Faces that will be in contact with the adhesive must be dry, clean and free; from dust and grease.; Secure supply hose (6) to the chain lubrication system bracket with cable; strap (5).; Insert supply hose (6) through holder (4).; Secure supply hose (6) to rear wheel swinging arm (1) with cable straps (3); and (2).; (-) Installing bracket for supply tube nozzle; Install supply nozzle (1) with hose clamp (2) and cable strap (3) on holder; (4).; Install holder (2) with screw (1) under chain guard (3). | · p. PDF 958 |
| Motor | Acoustics screw to cylinder head | 10,0 N·m | — | — | · p. PDF 26 |
| Motor | Bypass distributor to cylinder head | 5,0 N·m | — | — | · p. PDF 26 |
| Motor | Camshaft bearing cap to cylinder head | 5,0 N·m | — | Contexto da tabela: M7 x 38 Tightening sequence: See repair; manual | · p. PDF 26 |
| Motor | Crankshaft main bearing, M10, not oiled Tightening sequence: Additional | 10,0 N·m | — | Contexto da tabela: angle of rotation 1-6; 80°; Engine block, bottom, to engine block, top, M8, not oiled Tightening sequence: Additional; angle of rotation 7-16; 80°; Engine block, bottom, to engine block, top, M6, not oiled Tightening sequence: Torque 17-23 | · p. PDF 26 |
| Motor | Cylinder head cover to cylinder head | 10,0 N·m | — | — | · p. PDF 26 |
| Motor | Engine block, bottom, to engine block, top, M6, not oiled Tightening sequence: Initial torque | 5,0 N·m | — | — | · p. PDF 26 |
| Motor | Engine block, bottom, to engine block, top, M8, not oiled Tightening sequence: Initial torque | 5,0 N·m | — | Contexto da tabela: 7-16 | · p. PDF 26 |
| Motor | Screw plug (rocker arm shaft) to cylinder head | 10,0 N·m | — | — | · p. PDF 26 |
| Motor | Screw plug in engine housing | 25,0 N·m | — | — | · p. PDF 26 |
| Motor | Bracket for overheating protection on oil sump | 8,0 N·m | — | — | · p. PDF 27 |
| Motor | Cylinder head, right, to frame | 3,0 N·m | — | Contexto da tabela: Threaded bush M24 x 1.25 - 10.9 Tightening sequence: 1rst step,; tighten repeatedly Lubricate thread, Lubricant (Optimoly TA) | · p. PDF 27 |
| Motor | Engine housing cover, left, to crankcase | 20,0 N·m | — | — | · p. PDF 27 |
| Motor | Engine housing cover, right, to crankcase | 20,0 N·m | — | — | · p. PDF 27 |
| Motor | Oil drain plug in oil sump | 25,0 N·m | — | — | · p. PDF 27 |
| Motor | Screw plug (crankshaft) in crankcase | 10,0 N·m | — | — | · p. PDF 27 |
| Motor | Oil filter union to engine | 35,0 N·m | — | — | · p. PDF 28 |
| Motor | Oil pump pinion cover to engine housing | 10,0 N·m | — | — | · p. PDF 28 |
| Motor | Oil pump to engine housing | 10,0 N·m | — | — | · p. PDF 28 |
| Motor | Sprocket to camshaft | 19,0 N·m | — | — | · p. PDF 28 |
| Motor | Timing-chain tensioner to cylinder head | 15,0 N·m | — | — | · p. PDF 28 |
| Motor | Cylinder head to crankcase | 5,0 N·m | — | Contexto da tabela: M9 x 1.25 Tightening sequence: See repair; manual | · p. PDF 30 |
| Motor | Camshaft sensor to cylinder head | 10,0 N·m | — | — | · p. PDF 34 |
| Motor | Crankshaft sensor to left engine lid | 10,0 N·m | — | — | · p. PDF 34 |
| Motor | Holder to engine housing cover | 6,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); Holder to engine housing cover | · p. PDF 34 |
| Motor | Positive wire to starter motor | 5,0 N·m | — | — | · p. PDF 34 |
| Motor | Rotor to crankshaft | 150,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); Rotor to crankshaft | · p. PDF 34 |
| Motor | Spark plug to cylinder head | 12,0 N·m | — | — | · p. PDF 34 |
| Motor | Starter to engine block | 10,0 N·m | — | Contexto da tabela: Thread-locking compound (mechanical); Starter to engine block | · p. PDF 34 |
| Motor | Stator to engine lid | 10,0 N·m | — | — | · p. PDF 34 |
| Motor | Radiator bracket to cylinder head | 8,0 N·m | — | — | · p. PDF 37 |
| Motor | Thermostat housing to cylinder head | 10,0 N·m | — | — | · p. PDF 37 |
| Motor | Exhaust header to cylinder head | 14,0 N·m | — | — | · p. PDF 38 |
| Motor | Holder for front silencer to engine | 19,0 N·m | — | — | · p. PDF 38 |
| Motor | Clutch hub to drive shaft | 190,0 N·m | — | Contexto da tabela: lubricate with engine oil; Clutch hub to drive shaft; M20 x 1.5, Replace nut Tightening sequence: 1st | · p. PDF 39 |
| Motor | Eccentric plate (tooth backlash) to engine housing | 10,0 N·m | — | — | · p. PDF 40 |
| Motor | Transmission to engine housing | 18,0 N·m | — | Contexto da tabela: Thread-locking compound (Loctite 243, Medium strength); Transmission to engine housing | · p. PDF 40 |
| Motor | Footbrake cylinder to footrest plate | 8,0 N·m | — | — | · p. PDF 45 |
| Motor | Footbrake cylinder with heel guard to footrest plate | 8,0 N·m | — | — | · p. PDF 45 |
| Motor | Pushrod, footbrake cylinder | 6,0 N·m | — | — | · p. PDF 45 |
| Motor | Frame to engine | 100,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); Frame to engine | · p. PDF 49 |
| Motor | Retaining panel for centre stand to engine | 38,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); Retaining panel for centre stand to engine | · p. PDF 49 |
| Motor | Wiring harness (ground) to engine | 8,0 N·m | — | — | · p. PDF 54 |
| Motor | Crash bar, left, to engine protection bar, right | 6,0 N·m | — | — | · p. PDF 58 |
| Motor | Engine guard to bracket | 9,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); Engine guard to bracket | · p. PDF 58 |
| Motor | Engine protection bar on engine block | 19,0 N·m | — | — | · p. PDF 58 |
| Motor | Engine protection bar on side stand bearing support and engine | 19,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); Engine protection bar on side stand bearing support and engine | · p. PDF 58 |
| Motor | NOTICE | 19,0 N·m | — | Contexto da tabela: Transfer the parts to the new component; replace as necessary.; Core activity; (-) Removing holder for front silencer; Remove screws (1).; Remove the bracket (2).; (-) Installing holder for front silencer; Position bracket (2).; Install screws (1).; Holder for front silencer to engine | · p. PDF 79 |
| Motor | Seal new seal (1) in the areas shown (arrows). | 10,0 N·m | — | Contexto da tabela: Sealant; 3 - Bond 1209 07 58 9 062 376; Install new seal (4).; Position cylinder head cover (3), checking that the seal (4) is seated; correctly.; Install screws (2).; Cylinder head cover to cylinder head | · p. PDF 152 |
| Motor | Lubricant | 10,0 N·m | — | Contexto da tabela: Molykote D paste; Use a suitable tool to install valve shims (1). Also ensure that they are; attached in the groove on the valve (arrow).; Turn back the special tool and remove it.; Repeat the procedure for all the valves.; Lubricate all components with engine oil.; (-) Installing cam followers; Position rocker arms (1) on the intake side.; Install rocker arm shafts (2).; Install needle rollers (3), making sure that needle rollers (3) engage in the; recesses (arrows) of rocker arm shafts (2).; Position rocker arms (1) on the exhaust side.; Install rocker arm shafts (2).; Install the needle rollers (3), ensuring that the needle rollers (3) engage in; the recesses (arrows) of the rocker arm shafts (2).; Install screws (1) with sealing washers (2).; Screw plug (rocker arm shaft) to cylinder head | · p. PDF 156 |
| Motor | (-) Installing oil pan | 10,0 N·m | — | Contexto da tabela: Hold oil sump (2) in position at the crankcase (3).; Install screws (1) and tighten until hand-tight.; The oil sump (2) is not tensioned.; Tighten screws in the specified tightening sequence.; Oil pan to crankcase; M6 x 30 Tightening; sequence:; Tightening; sequence: see; Repair Manual | · p. PDF 160 |
| Motor | Install oil dipstick (1) in the new part (2). | 10,0 N·m | — | Contexto da tabela: Installing crankshaft sensor; Check O-ring (3) for damage; replace if necessary.; Hold crankshaft sensor (2) in position, paying attention to the O-ring (3); while doing so.; Install bolt (1).; Crankshaft sensor to left engine lid | · p. PDF 163 |
| Motor | encapsulated) | 6,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-; encapsulated); Install holder (4) and screw (5).; Holder to engine housing cover | · p. PDF 164 |
| Motor | Lay component on clean, white surface. | 10,0 N·m | — | Contexto da tabela: Clean sealing surface of engine housing cover and crankcase.; Cleaner; Brake cleaner 83 19 2 154 780; Position alternator (1) in engine housing cover (2).; Install screws (3).; Stator to engine lid | · p. PDF 164 |
| Motor | Install all short bolts (1) but do not tighten them. | 20,0 N·m | — | Contexto da tabela: Install all long bolts(2) but do not tighten them.; Tighten screws (1) to (12) in the sequence given.; Engine housing cover, left, to crankcase | · p. PDF 165 |
| Motor | (-) Installing right crankcase cover | 20,0 N·m | — | Contexto da tabela: Position engine housing cover (1).; Install new seals (2).; Install screws (3) and tighten until hand-tight.; Engine housing cover (1) is not tensioned.; Tighten screws in the specified tightening sequence.; Engine housing cover, right, to crankcase | · p. PDF 168 |
| Motor | Prior to assembly, lightly lubricate the freewheel with engine oil. | 35,0 N·m | — | Contexto da tabela: Threaded holes must be free of oil!; Insert the freewheel (1) in the free-wheel housing (3).; The collar (arrow) points to the magnet wheel (2).; Offset on freewheel housing (3) faces out.; Clean thread.; Install new screws (4).; Freewheel to alternator | · p. PDF 190 |
| Motor | Preparatory work | 15,0 N·m | — | Contexto da tabela: + 11 31 780; Preparatory work; => Removing and installing the rear-wheel stand special tool; (motorcycles without centre stand) (Description in item: 46 52 510,; Billed as a separate item); Core activity; (-) Removing timing-chain tensioner; Remove screw plug (1) with O-ring (2).; Remove the timing-chain tensioner (3) with O-ring (4).; (-) Installing timing chain tensioner; Check O-rings (2) and (4) and renew them if necessary.; Install timing-chain tensioner (3) and O-ring (4).; Install screw plug (1) with O-ring (2).; Timing-chain tensioner to cylinder head | · p. PDF 197 |
| Motor | Check | 19,0 N·m | — | Contexto da tabela: Insert socket wrench (No. 11 0 774) with the mark (arrow) up.; Twist intake camshaft (1) and exhaust camshaft (2) using the socket wrench; (No. 11 0 774) and, at the same time, try to push the holding fixture (No. 11; 0 772) with side B (1.6 ° and 1.7 °).; NOTICE; If the camshafts can only be turned with difficulty, loosen the chain sprocket; screws on the camshaft, if required.; Result:; Locking device can be pushed on for adjustment.; Measure:; Remove socket wrench (No. 11 0 774).; Tighten screws of camshaft sprockets (1) until hand-tight.; Sprocket to camshaft | · p. PDF 206 |
| Motor | Turn the crankshaft. | 19,0 N·m | — | Contexto da tabela: Tighten the screws of camshaft sprockets (1) that have not been tightened; yet, counter-hold the double flat if necessary.; Sprocket to camshaft | · p. PDF 207 |
| Motor | (-) Installing cylinder head cover | 10,0 N·m | — | Contexto da tabela: Install new seals (1).; Seal new seal (1) in the areas shown (arrows).; Sealant; 3 - Bond 1209 07 58 9 062 376; Install new seal (4).; Position cylinder head cover (3), checking that the seal (4) is seated; correctly.; Install screws (2).; Cylinder head cover to cylinder head | · p. PDF 214 |
| Motor | Connect oil pump (4) on intake pipe (3). | 10,0 N·m | — | Contexto da tabela: Lubricate new O-ring (2) with engine oil and install on intake pipe (3).; Connect oil pump (4) on intake pipe (3).; Install oil separator hose (6) and bolt (5).; Oil separator hose to oil pump | · p. PDF 224 |
| Motor | Insert oil pump piston (1) in chain (2). | 10,0 N·m | — | Contexto da tabela: Push oil pump piston (1) with chain (2) on to shaft (3) and let it engage in; two-flats (arrows).; Install the nut (4).; Oil-pump pinion to oil-pump shaft | · p. PDF 225 |
❓ Perguntas frequentes
As respostas abaixo são montadas somente com dados publicados nesta ficha.
Quantos litros de óleo vão na BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: 3.0 L com troca do filtro.
Qual é a taxa de compressão da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: 13.1:1.
Qual é a folga das válvulas da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: admissão: 0.11...0.20 mm; escape: 0.30...0.35 mm.
Quais são as medidas dos pneus da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: dianteiro: 90/90-21; traseiro: 150/70 R17.
Qual é a calibragem dos pneus da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: dianteiro: 2.2 bar; traseiro: 2.5 bar.
Qual bateria usa a BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: 12 V · 10 Ah.
Qual é a capacidade do tanque da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: 23 L.
Qual é a folga da corrente da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: 40...50 mm.
Qual é o câmbio da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: 6 marchas, engrenagens de engate constante integradas ao motor.
Quais são o diâmetro e o curso do motor da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: 84 mm × 77 mm.
Qual é o curso da suspensão da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: dianteiro: 230 mm; traseiro: 215 mm.
Quais são os freios da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: dianteiro: Dois discos de 305 mm, pinças flutuantes de 2 pistões; traseiro: Disco de 265 mm, pinça flutuante de 1 pistão.
Qual é a especificação do alternador da BMW F 850 GS Adventure K82 2018 a 2021?
A ficha técnica indica: 416 W.
Qual é o torque de Coolant drain plug to water pump na BMW F 850 GS Adventure K82 2018 a 2021?
6,0 N·m.
Qual é o torque de Radiator to bracket na BMW F 850 GS Adventure K82 2018 a 2021?
8,0 N·m.