CalibragemConfiança alta
Qual a calibragem dos pneus da BMW K 1600 GT 2011 a 2016?
Pressões publicadas: dianteiro 2.9 bar; traseiro 2.9 bar.
Fonte: BMW — documentação técnicaVer detalhe →
BMW K 1600 GT 2011 a 2016
Ficha técnica da BMW K 1600 GT 2011 a 2016, aplicação 2011 a 2016 com 3 especificações, 199 torques publicados. Consulte os dados disponíveis para esta geração e confirme ano, versão e mercado antes de qualquer serviço.
✓ Dados conferidos📅 2011–2016🏍️ Touring
•
Torque máximo20 Nm💨
Calibragem dianteira2.9 bar💨
Calibragem traseira2.9 bar⚡ Respostas técnicas confirmadas
Atalhos objetivos montados somente com dados publicados de confiança alta ou com origem técnica rastreável nesta geração.
Torque de apertoConfiança alta
Qual o torque de Warning na BMW K 1600 GT 2011 a 2016?
O torque publicado é 10,0 N·m.
Fonte: BMW — documentação técnicaVer detalhe →
⚙️ Motor, óleo e regulagens
Valores vinculados ao modelo e à faixa de anos desta ficha.
Torque máximoFonte técnica: BMW — documentação técnica20 Nm
⭕ Pneus e calibragem
Valores vinculados ao modelo e à faixa de anos desta ficha.
Calibragem dianteiraFonte técnica: BMW — documentação técnica2.9 bar
Calibragem traseiraFonte técnica: BMW — documentação técnica2.9 bar
🔧 Torques de aperto
Use ferramenta calibrada e confirme as notas específicas antes do serviço. Total encontrado: 199.
| Sistema | Componente | Torque | Rosca / quantidade | Notas | Fonte |
|---|---|---|---|---|---|
| Arrefecimento | Warning | 10,0 N·m | — | Contexto da tabela: Take care when working on the cooling system: risk of burns if the; system is hot.; Do not work on the cooling system until it has had ample time to cool; down.; Place a suitable container in position.; Remove screw (1).; Disconnect return line (2) for the coolant from the coolant pump, noting; O-ring (3).; Drain the coolant into the container.; (-) Filling and venting complete cooling system; Clean the tapped hole.; Check O-ring (3) for damage; replace if not in perfect condition.; Make sure that O-ring (3) is seated in the groove (arrow).; Push return line (2) for the coolant into the coolant pump.; Install new screw (1).; Coolant line to pump | · p. PDF 177 |
| Arrefecimento | Preparatory work | 3,0 N·m | — | Contexto da tabela: + 17 11 547; Preparatory work; Removing left bottom side panel; Removing left radiator cowl; Removing radiator hose cover; Removing right radiator cowl; Removing spoiler for radiator; Removing air guide for radiator; Core activity; (-) Removing screen; Remove screws (1).; Disengage dirt screen (2) and remove.; (-) Installing screen; Hold screen (2) in position.; Install screws (1).; Mesh screen and cooling-air guide to radiator | · p. PDF 188 |
| Arrefecimento | (-) Installing fan | 3,0 N·m | — | Contexto da tabela: Hold fan (2) in position.; Install screws (1).; Radiator cowl/screen to radiator | · p. PDF 191 |
| Arrefecimento | (-) Installing air guide with dirt deflector | 3,0 N·m | — | Contexto da tabela: Place air guide (3) with dirt deflector (2) in position.; Secure the holders (arrows) for dirt deflector (2).; Install screws (1).; Mesh screen and cooling-air guide to radiator | · p. PDF 192 |
| Arrefecimento | (-) Installing screen | 3,0 N·m | — | Contexto da tabela: Hold screen (2) in position.; Install screws (1).; Mesh screen and cooling-air guide to radiator | · p. PDF 192 |
| Arrefecimento | (-) Connecting feed line for coolant | 10,0 N·m | — | Contexto da tabela: Clean the tapped hole.; Check O-ring (3) for damage; replace if not in perfect condition.; Make sure that O-ring (3) is seated in the groove (arrow).; Push feed line (2) for the coolant into the coolant pump.; Install new screw (1).; Coolant line to pump | · p. PDF 195 |
| Arrefecimento | Install screws (1). | 3,0 N·m | — | Contexto da tabela: Radiator cowl/screen to radiator | · p. PDF 217 |
| Arrefecimento | Radiator cowl/screen to radiator | 3,0 N·m | — | — | · p. PDF 217 |
| Arrefecimento | Attention | 14,0 N·m | — | Contexto da tabela: + 34 32 644; Attention; Brake fluid attacks paintwork, plastic and rubber parts.; Do not allow brake fluid to come into contact with paintwork, plastic or; rubber parts.; Preparatory work; Removing left bottom side panel; Removing left radiator cowl; Removing left side panel; Draining front brake system; Core activity; (-) Removing brake line from pressure modulator; Unclip holder (1).; Slacken union screws (2) and (3).; Work brake line (4) clear and remove.; (-) Installing brake line from pressure modulator; Work brake line (4) into position and route it correctly.; Hold union screws (2) and (3) in position and tighten.; Brake line with union screw to components | · p. PDF 348 |
| Câmbio | Securing selector lever | 8,0 N·m | — | Contexto da tabela: Align shift lever (2) with the mark on the selector shaft (arrow) and slip; it into position.; Install screw (1).; Shift lever to gearbox selector shaft | · p. PDF 240 |
| Câmbio | Make sure that gearshift lever (4) with washer (5) do not slip out of | 28,0 N·m | — | Contexto da tabela: position.; Install new screw (2) and screws (1).; Footrest plate to frame | · p. PDF 249 |
| Câmbio | rider's toe joint. | 8,0 N·m | — | Contexto da tabela: Measure:; Installing gearshift lever; Slacken nuts (1) and (2).; Correct position of shift lever (3) by turning selector rod (4).; Technical data; Selector-rod rod- Screw-in screwed in at least; end setting depth in ball 3 full threads; socket and; rod end; Tighten nuts (1) and (2).; Ball end/rod end to selector rod | · p. PDF 251 |
| Câmbio | Preparatory work | 8,0 N·m | — | Contexto da tabela: + 23 41 555; Preparatory work; Removing gearbox cover; Disengaging shift lever; Core activity; (-) Removing selector rod; Remove screw (1) and remove shift lever (2) with washer (3).; Remove retaining clip (1).; Disengage selector rod (2) from shift lever (3) and remove.; (-) Adjusting selector rod length; Slacken nuts (1) and (2).; Adjust length (A).; Technical data; Basic setting of 273.9 +0.5−0.5 mm; selector rod; Tighten nuts (1) and (2).; Ball end/rod end to selector rod | · p. PDF 252 |
| Câmbio | (-) Installing selector rod | 19,0 N·m | — | Contexto da tabela: Install selector rod (2) and engage it on shift lever (3).; Install retaining clip (1).; Hold shift lever (2) with washer (3) in position and install screw (1).; Selector rod to shift lever | · p. PDF 253 |
| Câmbio | Hold footrest plate (4) in position, noting washer (5) and gearshift lever | 28,0 N·m | — | Contexto da tabela: Clean tapped hole for screw (2).; Hold footrest plate (4) in position, noting washer (5) and gearshift lever; (3), making sure that they do not slip out of position.; Install new screw (2) and screws (1).; Footrest plate to frame | · p. PDF 468 |
| Chassi/Carroceria | Install blanking plugs (1) in bores (2). | 66,0 N·m | — | Contexto da tabela: Install blanking plug (1) in bore (2).; (-) Installing side-stand pivot mount with side stand; Work line (3) for the side-stand switch up into position.; Hold the side-stand pivot mount with side stand (2) in position.; Install screws (1).; Pivot mount (side stand) to frame | · p. PDF 15 |
| Chassi/Carroceria | Equipment trim-level variant: | 10,0 N·m | — | Contexto da tabela: + 11 14 872; Equipment trim-level variant:; 0266 - Preparation for audio system and navigation device; 0267 - ECE audio system and preparation for navigation system; Preparatory work; Removing right bottom side panel; Core activity; (-) Removing right drop-protection pad; Remove screw (1) and screws (2).; Remove outer shell (3) with rubber damper (4).; (-) Replacing drop-protection pad; Transfer the necessary small items to the new drop-protection pad.; (-) Installing right drop-protection pad; Hold outer shell (3) with rubber damper (4) in position.; Install screws (2) and screw (1).; Cover of timing gear (with drop-protection pad) to crankcase | · p. PDF 60 |
| Chassi/Carroceria | (-) Installing right drop-protection pad | 10,0 N·m | — | Contexto da tabela: Hold outer shell (3) with rubber damper (4) in position.; Install screws (2) and screw (1).; Cover of timing gear (with drop-protection pad) to crankcase | · p. PDF 78 |
| Chassi/Carroceria | Locknut (bearing stud) to frame | 145,0 N·m | — | — | · p. PDF 288 |
| Chassi/Carroceria | Measure: | 40,0 N·m | — | Contexto da tabela: => 46 53 501, Replacing pivot mount for side stand (side stand removed); (Billed as a separate item); (-) Installing side stand; Clean the tapped hole.; Lubricate screw (1) and side stand (2) at the points indicated (arrows).; Fluids and lubricants; Klüberplex BE 11-462 Lubricant 83 22 0 397; 761; Insert pivot mount (3) into side stand (2).; Install new screw (1) and tighten.; Side stand to pivot mount | · p. PDF 403 |
| Chassi/Carroceria | Micro-encapsulated | 66,0 N·m | — | Contexto da tabela: (-) Installing side-stand pivot mount with side stand; Clean the tapped holes.; Hold the side-stand pivot mount with side stand (4) in position.; Install new screws (3).; Pivot mount (side stand) to frame | · p. PDF 403 |
| Chassi/Carroceria | Insert pivot mount (3) into side stand (2). | 40,0 N·m | — | Contexto da tabela: Install new screw (1) and tighten.; Side stand to pivot mount | · p. PDF 405 |
| Chassi/Carroceria | Preparatory work | 8,0 N·m | — | Contexto da tabela: + 46 54 505; Preparatory work; Remove the front seat; Remove the rear seat; Removing number-plate carrier; Removing complete luggage carrier; Core activity; (-) Removing luggage carrier; Remove screws (1).; Remove grab handles (2) left and (3) right from luggage carrier (4).; (-) Installing luggage carrier; Clean the tapped holes.; Hold grab handles (2) left and (3) right in position on luggage carrier; (4).; Make sure that the latching devices (arrows) engage in luggage carrier; (4).; Install new screws (1).; Grab handle to luggage carrier | · p. PDF 408 |
| Chassi/Carroceria | Core activity | 2,5 N·m | — | Contexto da tabela: + 46 63 830; Core activity; (-) Removing windscreen; Remove screws (1) and remove covers (2).; Remove windscreen (3).; (-) Installing windscreen; Hold windscreen (3) in position.; Hold covers (2) in position and install screws (1).; Standard screws for trim panels/body panels | · p. PDF 423 |
| Chassi/Carroceria | Front panel carrier to main frame | 8,0 N·m | — | — | · p. PDF 436 |
| Chassi/Carroceria | Installing operating unit for audio system | 1,5 N·m | — | Contexto da tabela: Install operating unit (2), making sure that the operating unit is located; in the catch (arrow).; Install screws (1).; Operating unit for audio system to fairing side panel | · p. PDF 454 |
| Chassi/Carroceria | Install screws (1). | 3,0 N·m | — | Contexto da tabela: Cover, centre to rear-light cluster | · p. PDF 539 |
| Chassi/Carroceria | (-) Installing right speaker | 2,5 N·m | — | Contexto da tabela: Install speaker (3).; Install screws (2).; Speaker to bracket/top section of fairing | · p. PDF 541 |
| Combustível | Open clip (1) with pliers (No. 17 5 500). | 6,0 N·m | — | Contexto da tabela: Disconnect oil return hose (2).; Remove oil-tank cap (3).; (-) Replacing oil tank cap; Transfer holders (1) to new oil tank cap (2).; Remove oil return pipe (3) with O-ring (4).; Check O-ring (4); replace if necessary.; Install oil return pipe (3) with O-ring (4) in new oil tank cap (2).; Return adapter in oil reservoir cap | · p. PDF 63 |
| Combustível | Install oil-tank cap (3) | 10,0 N·m | — | Contexto da tabela: Clean the sealing face of oil-tank cap (3).; Install oil-tank cap (3); Connect oil return hose (2) with clip (1).; Install clip (1) with pliers (No. 17 5 500).; Install oil-tank cap (3); Hold bracket for breather line (2) in position and install screws (1).; Cover of oil tank to crankcase; M6 x 25 tighten in; diagonally; opposite; sequence | · p. PDF 64 |
| Combustível | Install screw (1) with washer (2). | 19,0 N·m | — | Contexto da tabela: Fuel tank to main frame, front | · p. PDF 156 |
| Combustível | Remove screw (1) with washer (2). | 14,0 N·m | — | Contexto da tabela: Remove screws (3) with shouldered bushings (4).; Remove fuel tank (5).; (-) Installing fuel tank; Hold fuel tank (5) in position.; Install screws (3) with shouldered bushings (4).; Fuel tank to main frame, rear | · p. PDF 156 |
| Combustível | Tank holder, front, to main frame | 8,0 N·m | — | Contexto da tabela: Tighten screws (1) on left and right.; Tank holder, front, to main frame | · p. PDF 156 |
| Combustível | (-) Installing complete fuel filler cap | 3,0 N·m | — | Contexto da tabela: Check gasket (4) for damage; replace if necessary.; Install filler neck (3) with gasket (4).; Install screws (2).; Fuel filler cap to fuel tank | · p. PDF 161 |
| Combustível | Place retaining ring (1) for the cover of fuel tank in position. | 3,0 N·m | — | Contexto da tabela: Place outer ring with fuel filler cap (2) in position.; Install screws (1).; Fuel filler cap to fuel tank | · p. PDF 161 |
| Combustível | If the system is not refilled with fresh coolant, check the coolant to | 8,0 N·m | — | Contexto da tabela: ensure that the proportion of antifreeze is sufficient to ensure; resistance to freezing temperatures.; Technical data; Coolant, frost min −30 °C; protection; Fill the cooling system with coolant.; Technical data; Coolant, total Expansion 0.5 l; capacity tank; Coolant 3.5 l; system, total; Fluids and lubricants; Antifreeze; Air escapes initially, then coolant.; Tighten screw (1).; Vent screw in coolant pump | · p. PDF 178 |
| Combustível | Preparatory work | 2,0 N·m | — | Contexto da tabela: + 32 72 620; Preparatory work; Removing handlebar weight; Removing right multifunction switch; Core activity; (-) Removing throttle twistgrip; Remove screw (1).; Remove throttle twistgrip (2).; (-) Installing throttle twistgrip; Install throttle twistgrip (2).; Install screw (1).; Throttle twistgrip to handlebar | · p. PDF 268 |
| Direção | Stub handlebar to handlebar bridge | 19,0 N·m | — | — | · p. PDF 262 |
| Direção | Core activity | 19,0 N·m | — | Contexto da tabela: + 32 71 515; Core activity; (-) Removing handlebar weight; Remove screw (1).; Remove handlebar weight (2).; (-) Installing handlebar weight; Hold handlebar weight (2) in position.; Install screw (1).; Handlebar weight to handlebar half | · p. PDF 263 |
| Direção | Steering damper to frame | 19,0 N·m | — | — | · p. PDF 281 |
| Direção | clear and free from bubbles. | 2,2 N·m | — | Contexto da tabela: Close bleed screw (1).; Bleed screw to handlebar fitting | · p. PDF 312 |
| Direção | Close bleed screw (1). | 2,2 N·m | — | Contexto da tabela: Bleed screw to handlebar fitting | · p. PDF 319 |
| Direção | taking care not to affix the film over the mark. | 2,0 N·m | — | Contexto da tabela: Clean the area where the protective film will be applied.; Apply protective film (1), noting the mark (arrow) for alignment and; taking care not to affix the film over the mark.; Push complete grip unit (3) on to the handlebar.; Pull rubber grip (1) to the side and install screw (2).; Handlebar grip, left, to handlebar | · p. PDF 494 |
| Embreagem | Micro-encapsulated | 3,0 N·m | — | Contexto da tabela: (-) Installing right crankcase cover; Clean the sealing face.; Install sleeves (3).; Install crankcase cover (1) with gasket (2).; Install new screws (1) but do not tighten.; Tighten screws (1) to (13) in the specified sequence to the specified; initial torque.; Clutch cover to crankcase (initial torque) | · p. PDF 69 |
| Embreagem | Pressure plate to clutch hub | 10,0 N·m | — | — | · p. PDF 234 |
| Embreagem | Hold clutch line (1) in position at handlebar fitting (2). | 18,0 N·m | — | Contexto da tabela: Install banjo bolt (3) with new sealing rings (4), but do not tighten at; this point.; Position clutch line (1) at the stop (arrow) and tighten banjo bolt (1).; Clutch line to clutch lever fitting | · p. PDF 241 |
| Embreagem | Close the retaining strap (arrow). | 0,3 N·m | — | Contexto da tabela: (-) Securing clutch switch; Install clutch switch (2) with the white mark (arrow) pointing down,; noting locating point (3).; Install screw (1).; Clutch switch to handlebar fitting | · p. PDF 270 |
| Embreagem | Hold clutch hose (3) in position. | 18,0 N·m | — | Contexto da tabela: Install banjo bolt (1) with new sealing washers (2).; Clutch line to clutch lever fitting | · p. PDF 270 |
| Embreagem | (-) Installing clutch switch | 0,3 N·m | — | Contexto da tabela: Install clutch switch (2) with the white mark (arrow) pointing down,; noting locating point (3).; Install screw (1).; Clutch switch to handlebar fitting | · p. PDF 500 |
| Escape | (-) Installing tyre pressure monitoring control unit (RDC | 3,0 N·m | — | Contexto da tabela: control unit); Install RDC control unit (2).; Install screw (1).; Tyre pressure monitoring (RDC) control unit to intake air silencer | · p. PDF 150 |
| Escape | Install screw (3) with washer (4). | 8,0 N·m | — | Contexto da tabela: Intake air silencer to frame | · p. PDF 151 |
| Escape | (-) Installing intake air silencer front section | 3,0 N·m | — | Contexto da tabela: Install intake air silencer front section (1) with air filter (2).; Make sure that air filter (2) does not slip out of position and that the; retaining lugs (arrows) are engaged in holder (3).; Install screws (1).; Intake air silencer to filter housing | · p. PDF 152 |
| Freios | Hold brake hose (3) in position. | 24,0 N·m | — | Contexto da tabela: Install banjo bolt (1) with new sealing washers (2).; Brake hose with banjo bolt to components | · p. PDF 279 |
| Freios | Connect the brake bleeding device to bleed screw (1) in the left brake | 8,0 N·m | — | Contexto da tabela: caliper.; Slightly open bleed screw (1).; Continue bleeding the brake system until fresh brake fluid emerges.; Warning; The brake-bleeding process might have been interrupted even though; air remained in the system. On account of the vacuum extraction; process, it is not possible to tell whether the brake fluid extracted from; the system is free of bubbles.; On conclusion of the process, bleed the system manually (without; vacuum extraction) until you are sure that the brake fluid expelled from; the system is free of bubbles.; Close bleed screw (1) of the left brake caliper.; Bleed screw in front brake caliper | · p. PDF 311 |
| Freios | Install locking pin (2) with the bore (arrow) facing up and secure it with | 3,0 N·m | — | Contexto da tabela: split-pin keeper (1).; Hold brake-pad spring (2) in position and install screws (1).; Sheet metal spring on front brake caliper | · p. PDF 313 |
| Freios | Warning | 14,0 N·m | — | Contexto da tabela: The brake-bleeding process might have been interrupted even though; air remained in the system. On account of the vacuum extraction; process, it is not possible to tell whether the brake fluid extracted from; the system is free of bubbles.; On conclusion of the process, bleed the system manually (without; vacuum extraction) until you are sure that the brake fluid expelled from; the system is free of bubbles.; Close bleed screw (1) and remove the brake bleeding device.; Bleed screw, rear, in banjo bolt | · p. PDF 315 |
| Freios | Top up with fresh brake fluid to the (MAX) mark. | 14,0 N·m | — | Contexto da tabela: Fluids and lubricants; Brake fluid Hydraulic systems; Connect the brake bleeding device to bleed screw (1) in the brake; caliper.; Slightly open the bleed screw.; Warning; Air can be drawn into the system through the fluid replenishing hole if; the fluid level in the reservoir is too low; the system has to be bled; again if this happens.; Make sure that the fluid replenishing bore is always under the surface; of the brake fluid throughout the entire process of fluid changing/system; bleeding.; Continue bleeding the brake system until fresh brake fluid emerges.; Warning; The brake-bleeding process might have been interrupted even though; air remained in the system. On account of the vacuum extraction; process, it is not possible to tell whether the brake fluid extracted from; the system is free of bubbles.; On conclusion of the process, bleed the system manually (witho | · p. PDF 321 |
| Freios | Hold brake-pad spring (2) in position and install screws (1). | 3,0 N·m | — | Contexto da tabela: Sheet metal spring on front brake caliper | · p. PDF 334 |
| Freios | Install brake pipe (3) with banjo bolt (1) and new sealing rings (2). | 24,0 N·m | — | Contexto da tabela: Brake hose with banjo bolt to components | · p. PDF 335 |
| Freios | Preparatory work | 28,0 N·m | — | Contexto da tabela: + 34 11 560; Preparatory work; Draining front brake system; Removing front brake pads; Core activity; (-) Removing front brake caliper; Attention; Brake fluid attacks paintwork, plastic and rubber parts.; Do not allow brake fluid to come into contact with paintwork, plastic or; rubber parts.; Remove banjo bolt (1) with sealing rings (2).; Remove screws (3).; Remove brake caliper (4).; (-) Installing front brake caliper; Secure brake caliper (5) with screws (4).; Front brake caliper to wheel carrier | · p. PDF 335 |
| Freios | (-) Installing front right brake disc | 19,0 N·m | — | Contexto da tabela: Clean the tapped holes in the wheel rim.; Lay brake disc (2) on the wheel rim with the wide flats (arrow) of the; rivets to the outside and position it correctly.; Install new screws (1).; Brake disc to front wheel; Flat-head screw, M8 x 27 - 10.9, tighten in; Replace screw diagonally; Micro-encapsulated opposite; sequence | · p. PDF 337 |
| Freios | Disengage brake hose (3) from brake caliper (4). | 24,0 N·m | — | Contexto da tabela: Unclip holder (1) from brake hose (2).; Work brake hose (2) to the rear and disengage it from bracket (3) for; the thrust link and holder (4) for the brake hose.; (-) Installing rear brake hose; Seat brake hose (2) in bracket (3) for the thrust link and bracket (4) for; the brake hose.; Position brake hose (2) and clip in holder (1).; Hold brake hose (3) in position at brake caliper (4).; Install banjo bolt (1) with new sealing rings (2).; Brake hose with banjo bolt to components | · p. PDF 343 |
| Freios | Clip holder (1) to brake hose (2). | 14,0 N·m | — | Contexto da tabela: Hold brake line (2) in position at connector (3) for brake hose and; secure union screw (1).; Brake line with union screw to components | · p. PDF 344 |
| Freios | Hold brake hose (2) in position at frame (4). | 8,0 N·m | — | Contexto da tabela: Align brake hose (2) and install screw (3).; Brake hose, rear, to frame | · p. PDF 344 |
| Freios | Clip brake line (2) into holder (1). | 14,0 N·m | — | Contexto da tabela: Tighten down union screw (3).; Brake line with union screw to components | · p. PDF 346 |
| Freios | Disengage union screw (1). | 14,0 N·m | — | Contexto da tabela: Unclip brake line (2) from holder (3) and remove.; (-) Installing brake line to pressure modulator; Work brake line (2) into position and route it correctly.; Clip brake pipe (2) into holder (3).; Tighten union screw (1).; Brake line with union screw to components | · p. PDF 346 |
| Freios | Clip brake pipe (2) into holder (3). | 14,0 N·m | — | Contexto da tabela: Install bracket (1).; Hold brake line (2) in position at pressure modulator (3) and tighten; union screw (1).; Brake line with union screw to components | · p. PDF 352 |
| Freios | Clip brake line (1) into holder (2). | 14,0 N·m | — | Contexto da tabela: Secure the cable tie (arrow).; Hold brake line (2) in position at connector (3) for brake hose and; secure union screw (1).; Brake line with union screw to components | · p. PDF 356 |
| Freios | Hold brake line (2) in position at pressure modulator (3) and tighten | 14,0 N·m | — | Contexto da tabela: union screw (1).; Brake line with union screw to components | · p. PDF 356 |
| Freios | Brake line, front, to bracket for pressure modulator | 8,0 N·m | — | — | · p. PDF 361 |
| Geral | Collared nut, M24 x 1.25 2nd step | 100,0 N·m | — | — | · p. PDF 13 |
| Geral | Micro-encapsulated | 10,0 N·m | — | Contexto da tabela: (-) Securing oil lines; Check sealing rings (4) for damage; replace if necessary.; Install feed line (2) and return line (3).; Install screws (1).; Oil cooler lines to crankcase | · p. PDF 15 |
| Geral | Installing drain plug for oil pan | 28,0 N·m | — | Contexto da tabela: Install drain plug (1) with new sealing ring neuem Dichtring (2).; Oil drain plug to oil pan | · p. PDF 21 |
| Geral | Closing torque, | 20,0 N·m | — | Contexto da tabela: 100°; Back off fully; Initial torque, | · p. PDF 41 |
| Geral | (-) Installing sump plate | 10,0 N·m | — | Contexto da tabela: Place new gasket (2) and sump plate (1) in position.; Hold reinforcement (2) in position.; Install screws (1).; Reinforcement/sump plate to oil pan | · p. PDF 56 |
| Geral | (-) Installing oil pan | 10,0 N·m | — | Contexto da tabela: Clean the tapped holes.; Place new gasket (2) and oil pan (1) in position.; Install new screws (1), but do not tighten at this point.; Tighten screws (1).; Oil pan with sump plate to crankcase; M6 x 20, Replace screw Start at the middle; Micro-encapsulated and work outward; when tightening | · p. PDF 57 |
| Geral | Core activity | 10,0 N·m | — | Contexto da tabela: + 11 14 873; Core activity; (-) Removing left drop-protection pad; Remove screws (1) and (2).; Remove outer shell (3) with rubber damper (4).; (-) Installing left drop-protection pad; Hold rubber damper (4) with outer shell (3) in position.; Install screws (1) and (2).; Drop-protection pad, left, to crankcase | · p. PDF 61 |
| Geral | (-) Installing input shaft for oil pump | 15,0 N·m | — | Contexto da tabela: Install input shaft (3).; Install threaded plug (1) with new sealing ring (2).; Threaded plug (shaft for oil-pump drive) in crankcase | · p. PDF 100 |
| Geral | (-) Installing suction pipe for oil pump | 10,0 N·m | — | Contexto da tabela: Check O-ring (3) for damage; replace if necessary.; Hold suction pipe (2) with O-ring (3) in position.; Install screws (1).; Suction pipe to crankcase (return pump) | · p. PDF 100 |
| Geral | Install screws (1). | 10,0 N·m | — | Contexto da tabela: Oil pump to crankcase | · p. PDF 100 |
| Geral | Install screws (3) uniformly. | 8,0 N·m | — | Contexto da tabela: Intake assembly to crankcase | · p. PDF 108 |
| Geral | (-) Securing multi-controller | 1,5 N·m | — | Contexto da tabela: Position multi-controller (4) on grip (5). Make sure that the retainers; (arrows) and recesses (6) engage.; Work the cable of plug (3) for the heated grip through bracket (2).; Hold bracket (2) in position and install screws (1), noting the grip-; heating cable.; Multi-controller to grip | · p. PDF 274 |
| Geral | Install screw (1). | 9,0 N·m | — | Contexto da tabela: Capping screw, bearing stud, left | · p. PDF 287 |
| Geral | Optimoly TA Loosen | 7,0 N·m | — | — | · p. PDF 287 |
| Geral | Micro-encapsulated opposite | 19,0 N·m | — | Contexto da tabela: sequence | · p. PDF 337 |
| Geral | (-) Installing pressure modulator | 8,0 N·m | — | Contexto da tabela: Hold pressure modulator (4) with the bracket in position.; Install nuts (3).; Bracket for pressure modulator to vibration damper | · p. PDF 360 |
| Geral | Pressure modulator to bracket | 8,0 N·m | — | — | · p. PDF 360 |
| Geral | (-) Replacing front panel carrier, left | 10,0 N·m | — | Contexto da tabela: Remove screws (1) and remove bracket (2) for the speaker from front; panel carrier (3).; Transfer the following parts to new front panel carrier (1) :; Bracket (2) for the cable ties; Bracket (3) for the flow line to oil cooler; Bracket (4) for the return line from oil cooler; Rubber grommets (5); Rubber plug (6); Rubber grommet (7) with metal bushing.; Hold bracket (2) for speaker in position on new front panel carrier (3); and install screws (1).; Bracket for speaker to front panel carrier | · p. PDF 434 |
| Geral | Hold earthing strap (5) for the aerial in position and install screw (4). | 8,0 N·m | — | Contexto da tabela: Earthing strap (aerial) to front panel carrier | · p. PDF 435 |
| Geral | Transfer the following parts to new front panel carrier (1) : | 10,0 N·m | — | Contexto da tabela: Rubber grommet (2) with metal bushing; Rubber plug (3); Rubber grommet (4); Bracket (5) for cable ties.; Hold bracket (2) for speaker in position on new front panel carrier (3); and install screws (1).; Bracket for speaker to front panel carrier | · p. PDF 435 |
| Geral | (-) Replacing inner trim | 5,0 N·m | — | Contexto da tabela: Transfer the following components to new inner trim (4):; Flat nuts (1); Bushings (2); Rubber grommets (3); (-) Installing instrument panel; Install instrument panel (2) in inner trim (3).; Install screws (1).; Instrument panel to inner trim | · p. PDF 457 |
| Geral | Equipment trim-level variant: | 5,0 N·m | — | Contexto da tabela: + 51 16 554; Equipment trim-level variant:; 0266 - Preparation for audio system and navigation device; 0267 - ECE audio system and preparation for navigation system; Preparatory work; Removing air guide for intake air pipe, left; Removing left hand protector; Removing left speaker; Core activity; (-) Removing left mirror; Remove screws (1).; Remove mirror (2).; (-) Installing left mirror; Install mirror (2).; Install screws (1).; Mirror to front panel carrier | · p. PDF 473 |
| Geral | Remove screws (1). | 1,5 N·m | — | Contexto da tabela: Lift bracket (2) and work the cable from plug (3) for the heated grip; clear.; Remove bracket (2) and multi-controller (4) from grip (5).; (-) Installing multi-controller; Position multi-controller (4) on grip (5). Make sure that the retainers; (arrows) and recesses (6) engage.; Work the cable of plug (3) for the heated grip through bracket (2).; Hold bracket (2) in position and install screws (1), noting the grip-; heating cable.; Multi-controller to grip | · p. PDF 488 |
| Ignição/Elétrica | Connect plug (3) for the coolant-temperature sensor. | 8,0 N·m | — | Contexto da tabela: Connect plug (4) for the alternator.; Hold positive lead (3) for the alternator in position; Install nut (2).; Wiring harness to alternator | · p. PDF 17 |
| Ignição/Elétrica | Install cap (1). | 8,0 N·m | — | Contexto da tabela: Secure the cable in the clips (arrows).; Hold cable (3) for the starter in position.; Install nut (2).; Wiring harness to starter | · p. PDF 17 |
| Ignição/Elétrica | (-) Installing coolant pump | 10,0 N·m | — | Contexto da tabela: Check O-ring (3) for damage; replace if necessary.; Note the routing of oxygen-sensor cable (4).; Install coolant pump (2), making sure that the drive engages (arrows).; Install screws (1).; Coolant pump to crankcase | · p. PDF 100 |
| Ignição/Elétrica | (-) Installing left oxygen sensor | 25,0 N·m | — | Contexto da tabela: Thinly lubricate threads of oxygen sensor (1).; Fluids and lubricants; Optimoly TA High-temperature 18 21 9 062; assembly grease 599; Install oxygen sensor (1).; Oxygen sensor to exhaust manifold | · p. PDF 113 |
| Ignição/Elétrica | Remove oxygen sensor (1). | 25,0 N·m | — | Contexto da tabela: (-) Installing right oxygen sensor; Thinly lubricate threads of oxygen sensor (1).; Fluids and lubricants; Optimoly TA High-temperature 18 21 9 062; assembly grease 599; Install oxygen sensor (1).; Oxygen sensor to exhaust manifold | · p. PDF 115 |
| Ignição/Elétrica | Hold positive lead (3) for the starter in position. | 8,0 N·m | — | Contexto da tabela: Install nut (2).; Wiring harness to starter | · p. PDF 125 |
| Ignição/Elétrica | Wiring harness to alternator | 8,0 N·m | — | — | · p. PDF 125 |
❓ Perguntas frequentes
As respostas abaixo são montadas somente com dados publicados nesta ficha.
Qual é a calibragem dos pneus da BMW K 1600 GT 2011 a 2016?
A ficha técnica indica: dianteiro: 2.9 bar; traseiro: 2.9 bar.
Qual é o torque de Warning na BMW K 1600 GT 2011 a 2016?
10,0 N·m — Contexto da tabela: Take care when working on the cooling system: risk of burns if the; system is hot.; Do not work on the cooling system until it has had ample time to cool; down.; Place a suitable container in position.; Remove screw (1).; Disconnect return line (2) for the coolant from the coolant pump, noting; O-ring (3).; Drain the coolant into the container.; (-) Filling and venting complete cooling system; Clean the tapped hole.; Check O-ring (3) for damage; replace if not in perfect condition.; Make sure that O-ring (3) is seated in the groove (arrow).; Push return line (2) for the coolant into the coolant pump.; Install new screw (1).; Coolant line to pump.
Qual é o torque de Preparatory work na BMW K 1600 GT 2011 a 2016?
3,0 N·m — Contexto da tabela: + 17 11 547; Preparatory work; Removing left bottom side panel; Removing left radiator cowl; Removing radiator hose cover; Removing right radiator cowl; Removing spoiler for radiator; Removing air guide for radiator; Core activity; (-) Removing screen; Remove screws (1).; Disengage dirt screen (2) and remove.; (-) Installing screen; Hold screen (2) in position.; Install screws (1).; Mesh screen and cooling-air guide to radiator.