CalibragemConfiança alta
Qual a calibragem dos pneus da BMW K 1600 GT 2011 a 2016?
Pressões publicadas: dianteiro 2.9 bar; traseiro 2.9 bar.
Fonte: BMW — documentação técnicaVer detalhe →
BMW K 1600 GT 2011 a 2016
Ficha técnica da BMW K 1600 GT 2011 a 2016, aplicação 2011 a 2016 com 3 especificações, 199 torques publicados. Consulte os dados disponíveis para esta geração e confirme ano, versão e mercado antes de qualquer serviço.
✓ Dados conferidos📅 2011–2016🏍️ Touring
•
Torque máximo20 Nm💨
Calibragem dianteira2.9 bar💨
Calibragem traseira2.9 bar⚡ Respostas técnicas confirmadas
Atalhos objetivos montados somente com dados publicados de confiança alta ou com origem técnica rastreável nesta geração.
Torque de apertoConfiança alta
Qual o torque de Warning na BMW K 1600 GT 2011 a 2016?
O torque publicado é 10,0 N·m.
Fonte: BMW — documentação técnicaVer detalhe →
⚙️ Motor, óleo e regulagens
Valores vinculados ao modelo e à faixa de anos desta ficha.
Torque máximoFonte técnica: BMW — documentação técnica20 Nm
⭕ Pneus e calibragem
Valores vinculados ao modelo e à faixa de anos desta ficha.
Calibragem dianteiraFonte técnica: BMW — documentação técnica2.9 bar
Calibragem traseiraFonte técnica: BMW — documentação técnica2.9 bar
🔧 Torques de aperto
Use ferramenta calibrada e confirme as notas específicas antes do serviço. Total encontrado: 199.
| Sistema | Componente | Torque | Rosca / quantidade | Notas | Fonte |
|---|---|---|---|---|---|
| Ignição/Elétrica | (-) Installing oil-level/oil-temperature sensor | 10,0 N·m | — | Contexto da tabela: Check O-ring (3) for damage; replace if necessary.; Carefully work oil-level/oil-temperature sensor (2) with O-ring (3) into; position and install.; Install screws (1).; Oil-level/oil-temperature sensor to oil tank cover | · p. PDF 129 |
| Ignição/Elétrica | (-) Installing fuel-pump unit | 35,0 N·m | — | Contexto da tabela: Check sealing ring (2) for damage; replace if necessary.; Lubricate sealing ring (2) at the seating face for the union nut.; Fluids and lubricants; Tyre mounting paste Assembly paste 81 22 0 433; 046; Install fuel pump (1) with sealing ring (2) in the fuel tank. Take care not; to allow lever-type sensor (4) and intake strainer (3) to snag on the fuel; tank and suffer damage.; Insert sealing ring (2) in the fuel tank and install fuel pump (1).; Position fuel pump (1) in the locator (arrow).; Install union nut (2) with pin wrench (No. 16 1 021). Make sure that; retaining ring (3) does not turn at the same time.; Fuel pump to fuel tank | · p. PDF 161 |
| Ignição/Elétrica | Tyre mounting paste Assembly paste 81 22 0 433 | 35,0 N·m | — | Contexto da tabela: 046; Install fuel pump (1) with sealing ring (2) in the fuel tank. Take care not; to allow lever-type sensor (4) and intake strainer (3) to snag on the fuel; tank and suffer damage.; Position fuel pump (1) in the locator (arrow).; Install union nut (2) with pin wrench (No. 16 1 021). Make sure that; retaining ring (3) does not turn at the same time.; Fuel pump to fuel tank | · p. PDF 170 |
| Ignição/Elétrica | (-) Installing expansion tank for coolant | 6,0 N·m | — | Contexto da tabela: Connect hose (1) to expansion tank (3) in such a way that the lug; (arrow) engages the recess of the hose.; Close clip (2) with pliers (No. 17 5 571).; Remove hose clamp (No. 13 3 010).; Engage expansion tank (4).; Install screw (3).; Install screw (1) with washer (2).; Expansion tank to front panel carrier | · p. PDF 203 |
| Ignição/Elétrica | (-) Installing left silencer | 19,0 N·m | — | Contexto da tabela: Lubricating clamp for silencer; Thinly lubricate the inner face (arrow) of clamp (1).; Fluids and lubricants; Optimoly TA High-temperature 18 21 9 062; assembly grease 599; Slip clamp (1) on to silencer pipe (2).; Install silencer (3), slipping the guide (arrow) on to holder (4).; Install screw (1) with thrust washer (2).; Silencer to bracket | · p. PDF 219 |
| Ignição/Elétrica | Align clamp (2) with the retaining lug (arrow). | 30,0 N·m | — | Contexto da tabela: Tighten screw (1).; Clamp to silencer and exhaust manifold | · p. PDF 220 |
| Ignição/Elétrica | Click shift lever (1) up and down, making sure that there is adequate | 8,0 N·m | — | Contexto da tabela: clearance between shift lever (1) and clutch line (2).; If the clearance between clutch line and shift lever is not adequate,; reposition the clutch line.; Clip clutch line (1) centred at printed GT marking rings (arrows) into; holder (2).; Clip clutch line (1) into holders (3) and (4).; Clip clutch line (4) into holder (5).; Hold clip (3) in position and install screw (2), turning clip (3) counter-; clockwise and counter-holding.; Clamp with clutch line to frame steering head | · p. PDF 240 |
| Ignição/Elétrica | Micro-encapsulated | 19,0 N·m | — | Contexto da tabela: Hold ignition switch (3) in position and install screws (2).; Install screws (1).; (-) Installing handlebar bridge; Position left handlebar (5) on handlebar bridge (3).; Install screws (4).; Stub handlebar to handlebar bridge | · p. PDF 261 |
| Ignição/Elétrica | Technical data | 20,0 N·m | — | Contexto da tabela: Ignition Pilot hole min 5 mm; switch/steering diameter 4 mm; lock - drilling depth Diameter for 5 mm; for drilling out non- drilling out; removable screws fully 8.5 mm; Use compressed air to remove metal particles.; Remove steering lock (2) with ring aerial (3).; Use a stud remover to remove shanks of non-removable screws (4).; Clean the threads.; Install steering lock (2) with ring aerial (3) in new handlebar bridge (4).; Install non-removable screws (1) with socket wrench insert (No. 51 0; 531).; Ignition and steering lock to handlebar yoke | · p. PDF 261 |
| Ignição/Elétrica | Preparatory work | 19,0 N·m | — | Contexto da tabela: + 32 71 525; Preparatory work; Covering cover for fuel tank; Covering instrument panel; Removing handlebar weight; Removing left grip unit; Removing handlebar lever fitting for clutch; Closing equalising bore of front brake; Removing BMW badge with carrier; Removing nut of handlebar bridge; Disconnecting plugs for ignition switch/steering lock and ring; aerial; Core activity; (-) Removing left handlebar; Remove screws (1).; Remove handlebar (2) from handlebar bridge (3).; (-) Removing left handlebar; Position handlebar (2) on handlebar bridge (3).; Install screws (1).; Stub handlebar to handlebar bridge | · p. PDF 264 |
| Ignição/Elétrica | Hold clutch lever fitting (3) in position. | 5,0 N·m | — | Contexto da tabela: Hold clamp (2) in position and align with clutch fitting (3) at the mark; (arrow).; Install screws (1).; Handlebar fittings to handlebars | · p. PDF 270 |
| Ignição/Elétrica | Attention | 5,0 N·m | — | Contexto da tabela: + 32 72 638; Attention; Brake fluid attacks paintwork, plastic and rubber parts.; Do not allow brake fluid to come into contact with paintwork, plastic or; rubber parts.; Preparatory work; Draining brake fluid reservoir on handbrake fitting; Core activity; (-) Removing handbrake fitting; Remove banjo bolt (1) with sealing washers (2).; Remove brake hose (3).; Remove screws (1) and clamp (2).; Remove handbrake fitting (3).; (-) Installing handbrake fitting; Hold handbrake fitting (3) in position.; Hold clamp (2) in position and align with handbrake fitting (3) at the; mark (arrow).; Install screws (1).; Handlebar fittings to handlebars | · p. PDF 278 |
| Ignição/Elétrica | Connecting brake lines to pressure modulator | 14,0 N·m | — | Contexto da tabela: Attention; Stretched, twisted or incorrectly fitted brake lines can become worn and; start to leak.; Do not bend or clamp brake lines.; When fitting, check that they are correctly installed and secured and; are not stretched, bent or clamped. Make sure that clearance relative to; all other components is adequate in all situations.; Connect the following brake lines:; (6) for control circuit, rear wheel; (5) for brake circuit, rear wheel; (4) for brake circuit, front wheel; (3) for control circuit, front wheel; Tighten union screws (1) and (2).; Brake line with union screw to components | · p. PDF 361 |
| Ignição/Elétrica | Equipment trim-level variant: | 9,0 N·m | — | Contexto da tabela: 0530 - Tyre pressure monitoring (RDC); Core activity; (-) Removing front tyre pressure monitoring sensor (RDC; sensor); Remove screw (1).; Remove RDC sensor (2).; (-) Install the front tyre pressure monitoring sensor (RDC; sensor); Clean the seat and the threaded bore for the RDC sensor.; Parallel RDC sensor (1) with the wheel rim such that the plastic body; does not touch the wheel rim.; When installing, make sure that RDC sensor (2) and RDC label (3) on; the rim are aligned and install screw (1).; RDC sensor to wheel rim | · p. PDF 367 |
| Ignição/Elétrica | Remove screw (1). | 5,0 N·m | — | Contexto da tabela: Remove wheel-speed sensor (2).; (-) Installing front wheel-speed sensor; Clean the tapped hole.; Install wheel-speed sensor (2).; Install new screw (1).; Wheel-speed sensor to wheel carrier/ rear brake caliper | · p. PDF 372 |
| Ignição/Elétrica | Disengage cable (1) from holder (2). | 5,0 N·m | — | Contexto da tabela: Remove screw (3).; Remove wheel-speed sensor (4).; (-) Installing rear wheel-speed sensor; Clean the tapped hole.; Secure cable (1) in holder (2).; Install wheel-speed sensor (4).; Install new screw (3).; Wheel-speed sensor to wheel carrier/ rear brake caliper | · p. PDF 375 |
| Ignição/Elétrica | Clamping screw for quick-release axle to wheel carrier | 19,0 N·m | — | Contexto da tabela: Tighten screw (1).; Clamping screw for quick-release axle to wheel carrier | · p. PDF 379 |
| Ignição/Elétrica | Result: Battery too weak | 9,0 N·m | — | Contexto da tabela: Measure:; Replace the RDC sensor.; (-) Installing front tyre pressure monitoring sensor (RDC; sensor); Parallel RDC sensor (1) with the wheel rim such that the plastic body; does not touch the wheel rim.; Affix RDC label (3) at the position of RDC sensor (2).; Install screw (1).; RDC sensor to wheel rim | · p. PDF 385 |
| Ignição/Elétrica | (-) Installing rear tyre pressure monitoring sensor (RDC | 9,0 N·m | — | Contexto da tabela: Replace the RDC sensor.; (-) Installing rear tyre pressure monitoring sensor (RDC; sensor); Parallel RDC sensor (1) with the wheel rim such that the plastic body; does not touch the wheel rim.; Affix RDC label (3) at the position of RDC sensor (2).; Install screw (1).; RDC sensor to wheel rim | · p. PDF 388 |
| Ignição/Elétrica | (-) Installing right front panel carrier | 8,0 N·m | — | Contexto da tabela: Hold front panel carrier (2) in position, clip cable (3) for the ignition; switch to the inside of front panel carrier (2) and install screws (1).; Front panel carrier to main frame | · p. PDF 435 |
| Ignição/Elétrica | Route wiring harness (1) to front panel carrier (2) and secure it with the | 12,0 N·m | — | Contexto da tabela: cable ties (arrows).; (-) Installing left front panel carrier; Work left front panel carrier (1) into position, noting feed line (2) and; return line (3) of oil cooler (4).; Work oil cooler (4) with rubber mounts (5) into position from below; between right front panel carrier (6) and left front panel carrier (1).; Hold front panel carrier (3) in position, install screws (1) to secure the; front panel carrier to the front panel carrier and screws (2) to secure; the front panel carrier to the main frame.; Front panel carrier to front panel carrier | · p. PDF 436 |
| Ignição/Elétrica | Battery holder to rear carrier | 3,0 N·m | — | — | · p. PDF 484 |
| Ignição/Elétrica | Install protective cap (3) for positive terminal. | 3,5 N·m | — | Contexto da tabela: Hold negative lead in position at negative terminal of battery (2) and; install screw (1).; Wiring harness to battery | · p. PDF 484 |
| Ignição/Elétrica | install. | 20,0 N·m | — | Contexto da tabela: (-) Installing ignition switch/steering lock with ring aerial; Clean the tapped holes.; Install steering lock (2) with ring aerial (3) in handlebar bridge (4).; Install new non-removable screws (1) with socket wrench insert (No.; Ignition and steering lock to handlebar yoke | · p. PDF 519 |
| Ignição/Elétrica | (-) Installing height sensor, front | 5,0 N·m | — | Contexto da tabela: Hold sensor (2) in position, making sure that the position of the recess; (arrow) relative to the lug (3) is correct, and install screw (1).; Bracket for height sensor to front panel carrier | · p. PDF 528 |
| Ignição/Elétrica | Disengage headlight (1) from rubber grommets (2) and remove. | 1,5 N·m | — | Contexto da tabela: (-) Replacing headlight; Remove screws (1).; Remove the following components and transfer them to the new; headlight; check seals (4) for damage and replace if necessary:; Disengage side-light modules (2) and disconnect plugs (3); Side-light modules (2) with seals (4); Flat nuts (5); Install screws (1).; Mounted parts to headlight | · p. PDF 534 |
| Ignição/Elétrica | Remove screws (1). | 1,5 N·m | — | Contexto da tabela: Remove headlight control unit (2) with seal (3) and xenon control unit; (4) with seal (5) and install in new headlight. Check seals (3) and (5); for damage; replace if necessary.; Install screws (1).; Mounted parts to headlight | · p. PDF 534 |
| Ignição/Elétrica | Connect plug (4) for the headlight and secure it with cable in holder | 2,5 N·m | — | Contexto da tabela: (5).; Install retaining clip (1) and screw (2) with washer (3).; Headlight to front panel carrier | · p. PDF 535 |
| Ignição/Elétrica | Install retaining clip (1) and screw (2) with washer (3). | 2,5 N·m | — | Contexto da tabela: Headlight to front panel carrier | · p. PDF 535 |
| Motor | Hold threaded sleeve (3) and collared nut (2) in position and align with | 2,0 N·m | — | Contexto da tabela: the cylinder head, using suitable tools.; Tighten threaded sleeve (3) and collared nut (2), install screw (1).; Cylinder head, right, to frame; Threaded sleeve, M24 x 1.25 1st step | · p. PDF 13 |
| Motor | Remove the lengths of adhesive tape (arrows). | 66,0 N·m | — | Contexto da tabela: Tighten screws (1), (2) and (3).; Engine to frame, left side; Loosely install all; bushings and; screws on left and; right; Tighten screws on; left until hand-tight | · p. PDF 13 |
| Motor | (-) Securing wiring harness to engine | 8,0 N·m | — | Contexto da tabela: Hold earth cable (2) in position and install screw (1).; Wiring harness to crankcase | · p. PDF 16 |
| Motor | Install earth lead (2) with screws (1). | 8,0 N·m | — | Contexto da tabela: Engine wiring harness to cylinder head | · p. PDF 17 |
| Motor | Drain off all the engine oil. | 11,0 N·m | — | Contexto da tabela: Pouring in engine oil; Installing oil filter; Clean the sealing face on the engine block (arrow).; Wet sealing ring (3) of new oil filter (2) with engine oil.; Push shift lever (1) down.; Install new oil filter (2), using oil filter wrench (No. 11 4 661).; Oil filter to engine | · p. PDF 20 |
| Motor | Install coolant-temperature sensor (1) with new sealing ring (2). | 15,0 N·m | — | Contexto da tabela: Temperature sensor to cylinder head | · p. PDF 40 |
| Motor | Install cable (3) for the crankshaft sensor with holders (4). | 10,0 N·m | — | Contexto da tabela: Install radiator union (2) with screws (1).; Coolant adapter to cylinder head | · p. PDF 41 |
| Motor | Install screws (3). | 66,0 N·m | — | Contexto da tabela: Cylinder head, left, to frame | · p. PDF 41 |
| Motor | Install threaded sleeve (3), collared nut (2) and screw (1) and tighten. | 2,0 N·m | — | Contexto da tabela: Cylinder head, right, to frame; Threaded sleeve, M24 x 1.25 1st step | · p. PDF 41 |
| Motor | Connect plug (3) for the coolant-temperature sensor. | 14,0 N·m | — | Contexto da tabela: (-) Installing logotype; Hold logotype (2) in position.; Lubricate screw (1) and install.; Fluids and lubricants; Staburags NBU 30 PTM High-performance 07 55 9 056; lubricating grease 992; Seat cover (1) with the top lugs (arrows).; Clip cover (1) into position.; (-) Installing exhaust manifold, right; Install gaskets (3), making sure they are correctly positioned.; Hold exhaust manifold (2) in position and install nuts (1).; Exhaust header to cylinder head | · p. PDF 42 |
| Motor | Engine wiring harness to cylinder head | 8,0 N·m | — | — | · p. PDF 42 |
| Motor | (-) Securing right oxygen sensor | 14,0 N·m | — | Contexto da tabela: Route cable (1) behind coolant pump (3).; Route cable (1) for the oxygen sensor and secure it in holders (2).; Route cable (1) for the oxygen sensor and secure it in holders (2).; (-) Installing exhaust manifold, left; Install gaskets (3), making sure they are correctly positioned.; Hold exhaust manifold (2) in position and install nuts (1).; Exhaust header to cylinder head | · p. PDF 43 |
| Motor | Camshaft bearing cap to cylinder head | 10,0 N·m | — | Contexto da tabela: M6 tighten uniformly,; working from the; inside toward the; outside | · p. PDF 48 |
| Motor | Remove stud bolts with thrust nuts (No. 11 0 812) from the spark-plug | 8,0 N·m | — | Contexto da tabela: bores.; (-) Installing timing chain tensioner; Check sealing ring (1) for damage; replace if necessary.; Position sealing ring (1) in the groove (arrow) of cover (2).; Install timing-chain tensioner (4).; Install cover (2) with sealing ring (3) and install screws (1).; Cover of chain tensioner to cylinder head | · p. PDF 48 |
| Motor | Install screws (2) with seals (3). | 10,0 N·m | — | Contexto da tabela: Cylinder head cover to cylinder head (camshaft bearing cap) | · p. PDF 53 |
| Motor | (-) Installing suction pipe for engine oil | 10,0 N·m | — | Contexto da tabela: Check O-ring (3) for damage; replace if necessary.; Hold suction pipe (2) with O-ring (3) in position.; Install screws (1).; Suction pipe to crankcase (lube-oil pump) | · p. PDF 56 |
| Motor | Equipment trim-level variant: | 10,0 N·m | — | Contexto da tabela: + 11 14 802; Equipment trim-level variant:; 0266 - Preparation for audio system and navigation device; 0267 - ECE audio system and preparation for navigation system; Preparatory work; Removing right bottom side panel; Removing right drop-protection pad; Core activity; (-) Removing timing-gear cover; Remove screws (1).; Remove timing-gear cover (2) and sleeves (3).; (-) Installing timing-gear cover; Clean the sealing face (arrow) on the engine and in timing-gear cover; (2).; Apply a thin bead of sealing compound to the sealing face (arrow) of; the engine block.; Fluids and lubricants; Dow Corning Surface sealant 07 58 0 397; 777; Install sleeves (3).; Install timing-gear cover (2).; Install screws (1).; Cover of timing gear (with drop-protection pad) to crankcase | · p. PDF 59 |
| Motor | Preparatory work | 10,0 N·m | — | Contexto da tabela: + 11 14 858; Preparatory work; Removing left drop-protection pad; Core activity; (-) Removing crankshaft cover; Remove screws (1).; Remove crankshaft cover (2) with sealing ring (3).; (-) Installing crankshaft cover; Check sealing ring (1) for damage; replace if necessary.; Position sealing ring (1) in the groove (arrow) of crankshaft cover (2).; Clean the sealing face (arrow).; Place crankshaft cover (2) with sealing ring (3) in position.; Install screws (1).; Crankshaft cover to crankcase | · p. PDF 66 |
| Motor | (-) Installing timing-gear cover | 10,0 N·m | — | Contexto da tabela: Clean the sealing face (arrow) on the engine and in timing-gear cover; (2).; Apply a thin bead of sealing compound to the sealing face (arrow) of; the engine block.; Fluids and lubricants; Dow Corning Surface sealant 07 58 0 397; 777; Install sleeves (3).; Install timing-gear cover (2).; Install screws (1).; Cover of timing gear (with drop-protection pad) to crankcase | · p. PDF 78 |
| Motor | Check gasket (3) for damage; replace if necessary. | 10,0 N·m | — | Contexto da tabela: Clean the sealing faces (arrows) on the cylinder head.; Lay large gasket (1) in position on the cylinder head, noting the; position of the tabs (2) inside the cylinder head.; Place gasket (3) in position.; Place cylinder-head cover (1) in position.; Make sure that gaskets (2) and (3) do not slip out of position and are; not pinched out of shape.; Install screws (2) with seals (3).; Cylinder head cover to cylinder head (camshaft bearing cap) | · p. PDF 87 |
| Motor | (-) Installing oil pressure line | 40,0 N·m | — | Contexto da tabela: Check O-rings (3) and (4) for damage; replace if necessary.; Install oil pressure line (2).; Install oil filter union (1).; Oil filter union to engine | · p. PDF 101 |
| Motor | Transfer bracket (1) to new intake manifold (2). | 6,0 N·m | — | Contexto da tabela: Transfer sleeve (3) to new intake manifold (2).; Installing throttle-valve stub assembly; Check sealing ring (4) for damage; replace if necessary.; Install throttle-valve stub assembly (3) with sealing ring (4).; Hold retaining plate (2) in position.; Install screws (1).; Throttle-valve assembly to intake assembly | · p. PDF 106 |
| Motor | Connect plugs (2) for the injection valves. | 8,0 N·m | — | Contexto da tabela: Connect plug (1) for the fuel-pressure sensor.; Install screw (5).; Intake assembly to crankcase | · p. PDF 108 |
| Motor | Technical data | 12,0 N·m | — | Contexto da tabela: Spark plugs, NGK LMAR8AI-8; manufacturer and; designation; (-) Installing spark plugs; Install spark plugs (1) with spark-plug wrench (No. 12 3 611).; Spark plug in cylinder head | · p. PDF 119 |
| Motor | Core activity | 12,0 N·m | — | Contexto da tabela: (-) Removing spark plugs; Clean the spark-plug recess with compressed air.; Remove spark plugs (1) with spark-plug wrench (No. 12 3 611).; (-) Changing spark plugs; Install new spark plugs.; Technical data; Spark plugs, NGK LMAR8AI-8; manufacturer and; designation; (-) Installing spark plugs; Install spark plugs (1) with spark-plug wrench (No. 12 3 611).; Spark plug in cylinder head | · p. PDF 120 |
| Motor | (-) Installing alternator | 20,0 N·m | — | Contexto da tabela: Clean the sealing face (arrow).; Check O-ring (1) for damage; replace if necessary.; Clean the sealing face (arrow).; Check that judder dampers (1) are correctly positioned in the housing;; reposition if necessary.; Connect plug (6) for the alternator.; Install alternator (5).; Install screws (4).; Alternator to crankcase/alternator cover | · p. PDF 124 |
| Motor | Install cap (1). | 10,0 N·m | — | Contexto da tabela: (-) Installing starter; Clean the sealing faces.; Check the O-ring (arrow) for damage; replace if necessary.; Hold starter (5) in position.; Install screws (4).; Starter motor to gearbox housing | · p. PDF 125 |
| Motor | Throttle-valve assembly to intake assembly | 6,0 N·m | — | — | · p. PDF 138 |
| Motor | (-) Replacing intake air silencer | 3,0 N·m | — | Contexto da tabela: Remove rubber grommets (1), bushing (2), rubber grommet (3) and; condensate drain hose (4) from the old intake air silencer main section; and transfer them to the new component.; (-) Installing changeover valve for secondary air system; Check O-ring (arrow) for damage; replace if necessary.; Install changeover valve (2) with the O-ring (arrow).; Install screws (1).; Secondary air system changeover valve to intake air silencer | · p. PDF 149 |
| Motor | Continue filling the cooling system with coolant. | 8,0 N·m | — | Contexto da tabela: Technical data; Coolant, total Expansion 0.5 l; capacity tank; Coolant 3.5 l; system, total; Fluids and lubricants; Antifreeze; Air escapes initially, then coolant.; Tighten screw (1).; Breather screw to cylinder head | · p. PDF 178 |
| Motor | Manoeuvre oil cooler line (2) into position on the motorcycle. | 10,0 N·m | — | Contexto da tabela: Check sealing ring (3) for damage; replace if necessary.; Install sealing ring (3) on oil cooler line (2).; Connect oil cooler line (2) and clip the holder (arrow) to oil cooler line; (2).; Install screw (1).; Oil cooler lines to crankcase | · p. PDF 210 |
| Motor | (-) Installing exhaust manifold, left | 14,0 N·m | — | Contexto da tabela: Install gaskets (3), making sure they are correctly positioned.; Hold exhaust manifold (2) in position and install nuts (1).; Exhaust header to cylinder head | · p. PDF 222 |
| Motor | Remove nuts (1) and remove exhaust manifold (2). | 14,0 N·m | — | Contexto da tabela: Remove gaskets (3).; (-) Replacing exhaust manifold; Transfer flat nut (1) to new left-hand exhaust manifold (2).; Transfer flat nut (3) to new right-hand exhaust manifold (4).; (-) Installing exhaust manifold, right; Install gaskets (3), making sure they are correctly positioned.; Hold exhaust manifold (2) in position and install nuts (1).; Exhaust header to cylinder head | · p. PDF 222 |
| Motor | Engage 6th gear on the motorcycle and apply the rear brake. | 160,0 N·m | — | Contexto da tabela: Install nut (1).; Clutch to gearbox input shaft | · p. PDF 228 |
| Motor | catalogue (ETK). | 3,0 N·m | — | Contexto da tabela: Attention; Any mixture of oil, brake fluid and clutch fluid, even if the quantities; involved are minute, can attack and damage seals.; Always use separate sets of syringes and hoses for the individual; fluids, in order to avoid the risk of one fluid contaminating another.; Fill syringe (No. 34 2 551) to capacity with hydraulic fluid.; Connect syringe (No. 34 2 551) to bleed screw (1) and secure it with a; cable tie (arrow).; Back off bleed screw (1).; Use syringe (No. 34 2 551) to inject hydraulic fluid into the system; through bleed screw (1) until the fluid level in the reservoir is correct.; Technical data; Clutch fluid level with new Max mark on; clutch reservoir; liner,; motorcycle; upright; and; handlebars; centred; Fluids and lubricants; Vitamol V10; Tighten breather screw (1).; Bleed screw/grubscrew to clutch slave cylinder | · p. PDF 236 |
| Motor | Vitamol V10 | 3,0 N·m | — | Contexto da tabela: Wipe the rim of the reservoir, diaphragm (3) and cap (2) to remove; clutch fluid, carefully reassemble the components and install.; Install screws (1).; Remove bleed screw (2) and install grubscrew (1).; Bleed screw/grubscrew to clutch slave cylinder | · p. PDF 237 |
| Motor | Unclip clutch line (1) at GT marking rings (arrows) from holder (2). | 18,0 N·m | — | Contexto da tabela: Unclip clutch line (1) from holders (3) and (4).; Remove banjo bolt (1) with sealing rings (2).; Disengage clutch line (3) from slave cylinder (4) and remove.; (-) Installing clutch line; Route clutch line (3), position it correctly and hold it in position at slave; cylinder (4).; Install banjo bolt (1) with new sealing rings (2).; Clutch line to clutch slave cylinder | · p. PDF 239 |
| Motor | When installing gearbox (1), note breather hose (2) and drain hose (3) | 19,0 N·m | — | Contexto da tabela: and route them correctly.; Install complete gearbox (1).; Make sure that all gearbox components can be slipped easily into the; corresponding bearing seats in the engine block.; Install screws (1) and (2).; Gearbox to crankcase | · p. PDF 244 |
| Motor | selector shaft | 7,0 N·m | — | Contexto da tabela: Install lever unit (3), making sure that pushrod (5) engages in piston; seat (6) and that rubber sleeve (4) is correctly positioned.; Install screw (2) with new nut (1).; Handlebar lever to fitting | · p. PDF 272 |
| Motor | Brake fluid Hydraulic systems | 2,2 N·m | — | Contexto da tabela: Connect the brake bleeding device to bleed screw (1) in the handbrake; cylinder.; Slightly open bleed screw (1).; Continue bleeding the brake system until the fresh brake fluid emerges; clear and free from bubbles.; Close bleed screw (1).; Bleed screw to handlebar fitting | · p. PDF 311 |
| Motor | Fluids and lubricants | 2,2 N·m | — | Contexto da tabela: Brake fluid Hydraulic systems; Connect the brake bleeding device to bleed screw (1) in the handbrake; cylinder.; Slightly open bleed screw (1).; Continue bleeding the brake system until the fresh brake fluid emerges; clear and free from bubbles.; Close bleed screw (1).; Bleed screw to handlebar fitting | · p. PDF 318 |
| Motor | Hold footbrake cylinder (5) in position and install new screws (4). | 11,0 N·m | — | Contexto da tabela: Clean the threads.; Hold footbrake cylinder (5) in position and install new screws (4).; Footbrake cylinder to rear frame | · p. PDF 341 |
| Motor | Micro-encapsulated | 14,0 N·m | — | Contexto da tabela: Connect hose (3) and close hose clip (2) with pliers (No. 13 1 500).; Install locking clip (1).; Hold brake line (2) in position at footbrake cylinder (3) and tighten; union screw (1).; Brake line with union screw to components | · p. PDF 341 |
| Motor | Hold brake line (2) in position at footbrake cylinder (3) and tighten | 14,0 N·m | — | Contexto da tabela: union screw (1).; Brake line with union screw to components | · p. PDF 352 |
| Motor | programming) 3 FRUs | 1,5 N·m | — | Contexto da tabela: Equipment trim-level variant:; 0267 - ECE audio system and preparation for navigation system; 0266 - Preparation for audio system and navigation device; Note; Before removal, test the control unit with the BMW Motorrad diagnostic; system and make a backup copy of the data.; Preparatory work; Removing left bottom side panel; Removing left radiator cowl; Removing left side panel; Removing inner trim for left side panel; Core activity; (-) Removing operating unit for audio system; Remove screws (1).; Remove operating unit (2).; (-) Installing operating unit for audio system; Install operating unit (2), making sure that the operating unit is located; in the catch (arrow).; Install screws (1).; Operating unit for audio system to fairing side panel | · p. PDF 542 |
| Rodas/Pneus | Install nut (1). | 30,0 N·m | — | Contexto da tabela: Nut on leading-link quick-release axle | · p. PDF 258 |
| Rodas/Pneus | Locknut on quick-release axle/bearing stud | 145,0 N·m | — | — | · p. PDF 258 |
| Rodas/Pneus | Preparatory work | 60,0 N·m | — | Contexto da tabela: + 36 30 629; Preparatory work; Removing number-plate carrier; Core activity; (-) Remove the rear wheel; Remove screws (1).; Disengage rear wheel (2) and remove.; (-) Installing rear wheel; Install rear wheel (2).; Install screws (1).; Rear wheel to wheel flange; M10 x 1.25 x 40 tighten in; diagonally; opposite; sequence | · p. PDF 381 |
| Rodas/Pneus | Front-wheel cover, front, to front-wheel cover, rear | 2,5 N·m | — | — | · p. PDF 413 |
| Rodas/Pneus | Core activity | 2,5 N·m | — | Contexto da tabela: + 46 61 502; Core activity; (-) Remove the complete front-wheel cover; Remove screws (1).; Remove complete front-wheel cover (2).; (-) Disassembling front-wheel cover (rear section); Remove screws (1).; Remove front-wheel cover (front section) (2) from front-wheel cover; (rear section) (3).; (-) Assembling front-wheel cover (rear section); Position front-wheel cover (front section) (2) on front-wheel cover (rear; section) (3).; Install screws (1).; Front-wheel cover, front, to front-wheel cover, rear | · p. PDF 414 |
| Rodas/Pneus | Front-wheel cover to wheel carrier | 2,5 N·m | — | — | · p. PDF 415 |
| Suspensão | Remove screw (1). | 50,0 N·m | — | Contexto da tabela: Remove spring strut (2).; (-) Replacing spring strut; Install bushing (1) with collar (arrow) on left in forward direction of; travel in spring strut (2).; (-) Installing spring strut; Clean the tapped hole.; Lubricate the fitted head of screw (1).; Fluids and lubricants; Staburags NBU 30 PTM High-performance 07 55 9 056; lubricating grease 992; Install spring strut (2).; Install screw (1).; Spring strut, front, to frame and leading link | · p. PDF 256 |
| Suspensão | (-) Lowering front suspension | 15,0 N·m | — | Contexto da tabela: Lower front suspension (1) on scissor-type lifter (No. 00 1 571), and at; the same time guide the leading link (2) into position.; Clean quick-release axle (2) and lubricate the shank.; Fluids and lubricants; Optimoly TA High-temperature 18 21 9 062; assembly grease 599; Install quick-release axle (2).; Leading link (quick-release axle) to frame; M24 x 1.25 Initial torque, | · p. PDF 257 |
| Suspensão | (-) Securing spring strut at bottom | 50,0 N·m | — | Contexto da tabela: Clean the tapped hole.; Lubricate the fitted head of screw (1).; Fluids and lubricants; Staburags NBU 30 PTM High-performance 07 55 9 056; lubricating grease 992; Install screw (1) for spring strut (2).; Spring strut, front, to frame and leading link | · p. PDF 258 |
| Suspensão | Install screw (2) with washer (3) and new nut (1). | 50,0 N·m | — | Contexto da tabela: Relay plate to swinging arm and relay lever | · p. PDF 286 |
| Suspensão | Fluids and lubricants | 20,0 N·m | — | Contexto da tabela: Clean bearing stud (2) and lubricate at threads and bearing seat.; Fluids and lubricants; Optimoly TA High-temperature 18 21 9 062; assembly grease 599; Align the swinging arm and install bearing stud (2).; Floating bearing stud (swinging arm) to frame; M24 x 1.25 Initial torque, | · p. PDF 287 |
| Suspensão | Turn swinging arm (2) slightly and carefully work it into position in the | 9,0 N·m | — | Contexto da tabela: main frame.; Lift swinging arm (2) and secure it with ratchet strap (1) to footrest; bracket (3).; Slightly lubricate bearing stud (3) where shown here.; Fluids and lubricants; Staburags NBU 30 PTM High-performance 07 55 9 056; lubricating grease 992; Align swinging arm (4) and install bearing stud (3).; Install screws (2).; Bearing stud, swinging arm to frame, left | · p. PDF 287 |
| Suspensão | Clip spray-protection clip (1) to link strut (2). | 50,0 N·m | — | Contexto da tabela: Mechanical thread lock; Clip spray-protection clip (1) to link strut (2).; Tighten screw (1).; Spring strut/link strut to frame | · p. PDF 288 |
| Suspensão | Swing link strut (4) up and hold it in position. | 50,0 N·m | — | Contexto da tabela: Mechanical thread lock; Swing link strut (4) up and hold it in position.; Install screw (2) with washer (3) and nut (1).; Relay plate to swinging arm and relay lever | · p. PDF 288 |
| Suspensão | Swing relay plates (4) up and hold in position. | 42,0 N·m | — | Contexto da tabela: Install screw (2) with washer (3) and nut (1).; Deflectors to spring strut | · p. PDF 288 |
| Suspensão | Install screw (2) with washer (3) and nut (1). | 50,0 N·m | — | Contexto da tabela: Relay plate to swinging arm and relay lever | · p. PDF 294 |
| Suspensão | (-) Installing rear spring strut | 42,0 N·m | — | Contexto da tabela: Install spring strut (5).; Hold deflectors (4) in position on spring strut (5).; Install screw (2) with washer (3) and new nut (1).; Deflectors to spring strut | · p. PDF 296 |
| Suspensão | Work spring strut (2) into position in rear frame (3) and install by | 50,0 N·m | — | Contexto da tabela: Mechanical thread lock; Clean the tapped hole.; Work spring strut (2) into position in rear frame (3) and install by; moving rear frame (3).; Lubricate new screw (1) and install.; Spring strut/link strut to frame | · p. PDF 296 |
| Suspensão | Micro-encapsulated | 50,0 N·m | — | Contexto da tabela: Lubricate the fitted head,; Staburags NBU 30 PTM; Swing link strut (4) up and hold it in position.; Install screw (2) with washer (3) and new nut (1).; Relay plate to swinging arm and relay lever | · p. PDF 299 |
| Suspensão | Spring strut/link strut to frame | 50,0 N·m | — | — | · p. PDF 299 |
| Transmissão final | Lift out timing-chain tensioning rail (1). | 8,0 N·m | — | Contexto da tabela: (-) Installing timing-chain tensioner rail; Insert timing chain tensioning rail (1) from above.; Install pivot bearing screw (1).; Timing-chain rail to crankcase | · p. PDF 77 |
| Transmissão final | Work timing-chain slide rail (1) up to remove. | 8,0 N·m | — | Contexto da tabela: (-) Installing timing-chain slide rail; Insert timing chain slide rail (1) from above.; Install pivot bearing screw (1).; Timing-chain rail to crankcase | · p. PDF 82 |
| Transmissão final | Install drain plug (1) with O-ring (2). | 20,0 N·m | — | Contexto da tabela: Drain plug in bevel gears | · p. PDF 304 |
| Transmissão final | Use syringe (No. 34 2 551) to inject the gear oil slowly through the filler | 20,0 N·m | — | Contexto da tabela: neck into the housing.; Technical data; Bevel gears, oil oil change 180 ml; capacity Fluids and lubricants; Castrol SAF-XO; Installing oil filler plug, bevel gears; Check O-ring (2) for damage; replace if necessary.; Install oil filler plug (1) with O-ring (2).; Oil filler screw in cover of bevel gears | · p. PDF 304 |
| Transmissão final | (-) Installing bevel gears | 100,0 N·m | — | Contexto da tabela: Hold bevel gears (5) in position.; Clean the tapped hole in bearing stud (4).; Install bearing stud (4).; Check sealing ring (3) for damage; replace if necessary.; Install bearing stud (2) with sealing ring (3).; Install new screw (1), while counter-holding at bearing stud (4).; Bevel gears to swinging arm | · p. PDF 307 |
❓ Perguntas frequentes
As respostas abaixo são montadas somente com dados publicados nesta ficha.
Qual é a calibragem dos pneus da BMW K 1600 GT 2011 a 2016?
A ficha técnica indica: dianteiro: 2.9 bar; traseiro: 2.9 bar.
Qual é o torque de Warning na BMW K 1600 GT 2011 a 2016?
10,0 N·m — Contexto da tabela: Take care when working on the cooling system: risk of burns if the; system is hot.; Do not work on the cooling system until it has had ample time to cool; down.; Place a suitable container in position.; Remove screw (1).; Disconnect return line (2) for the coolant from the coolant pump, noting; O-ring (3).; Drain the coolant into the container.; (-) Filling and venting complete cooling system; Clean the tapped hole.; Check O-ring (3) for damage; replace if not in perfect condition.; Make sure that O-ring (3) is seated in the groove (arrow).; Push return line (2) for the coolant into the coolant pump.; Install new screw (1).; Coolant line to pump.
Qual é o torque de Preparatory work na BMW K 1600 GT 2011 a 2016?
3,0 N·m — Contexto da tabela: + 17 11 547; Preparatory work; Removing left bottom side panel; Removing left radiator cowl; Removing radiator hose cover; Removing right radiator cowl; Removing spoiler for radiator; Removing air guide for radiator; Core activity; (-) Removing screen; Remove screws (1).; Disengage dirt screen (2) and remove.; (-) Installing screen; Hold screen (2) in position.; Install screws (1).; Mesh screen and cooling-air guide to radiator.