Capacidade de óleoConfiança alta
Quantos litros de óleo vão na BMW R 1250 GS K50 2019 a 2022?
A ficha técnica indica 4 L com troca do filtro.
Fonte: BMW — documentação técnicaVer detalhe →
BMW R 1250 GS K50 2019 a 2022
Ficha técnica da BMW R 1250 GS K50 2019 a 2022, aplicação 2019 a 2022 com 12 especificações, 459 torques publicados. Consulte os dados disponíveis para esta geração e confirme ano, versão e mercado antes de qualquer serviço.
✓ Dados conferidos📅 2019–2022🏍️ Adventure
⚙️
Cilindrada1254 cm³📐
Taxa de compressão12.5:1•
Torque máximo140 Nm🛢️
Óleo com troca do filtro4 L📏
Folga de válvula — admissão0.10...0.17 mm📏
Folga de válvula - escape0.34...0.41 mm⛽
Capacidade do tanque20 L💨
Calibragem dianteira2.5 bar💨
Calibragem traseira2.9 bar⚡ Respostas técnicas confirmadas
Atalhos objetivos montados somente com dados publicados de confiança alta ou com origem técnica rastreável nesta geração.
CalibragemConfiança alta
Qual a calibragem dos pneus da BMW R 1250 GS K50 2019 a 2022?
Pressões publicadas: dianteiro 2.5 bar; traseiro 2.9 bar.
Fonte: BMW — documentação técnicaVer detalhe →
Folga de válvulasConfiança alta
Qual a folga de válvulas da BMW R 1250 GS K50 2019 a 2022?
Valores publicados: admissão 0.10...0.17 mm; escape 0.34...0.41 mm.
Fonte: BMW — documentação técnicaVer detalhe →
TanqueConfiança alta
Qual a capacidade do tanque da BMW R 1250 GS K50 2019 a 2022?
A capacidade publicada é 20 L.
Fonte: BMW — documentação técnicaVer detalhe →
Torque de apertoConfiança alta
Qual o torque de Coolant filler adapter in crankcase na BMW R 1250 GS K50 2019 a 2022?
O torque publicado é 5,0 N·m.
Fonte: BMW — documentação técnicaVer detalhe →
⚙️ Motor, óleo e regulagens
Valores vinculados ao modelo e à faixa de anos desta ficha.
CilindradaFonte técnica: BMW — documentação técnica1254 cm³
Taxa de compressãoFonte técnica: BMW — documentação técnica12.5:1
Torque máximoFonte técnica: BMW — documentação técnica140 Nm
Diâmetro do cilindroFonte técnica: BMW — documentação técnica102.5 mm
Óleo com troca do filtroFonte técnica: BMW — documentação técnica4 L
Curso do pistãoFonte técnica: BMW — documentação técnica76 mm
Folga de válvula — admissãoFonte técnica: BMW — documentação técnica0.10...0.17 mm
Folga de válvula - escapeFonte técnica: BMW — documentação técnica0.34...0.41 mm
⛽ Combustível e alimentação
Valores vinculados ao modelo e à faixa de anos desta ficha.
Capacidade do tanqueFonte técnica: BMW — documentação técnica20 L
⭕ Pneus e calibragem
Valores vinculados ao modelo e à faixa de anos desta ficha.
Calibragem dianteiraFonte técnica: BMW — documentação técnica2.5 bar
Calibragem traseiraFonte técnica: BMW — documentação técnica2.9 bar
📋 Ignicao
Valores vinculados ao modelo e à faixa de anos desta ficha.
Folga do eletrodo da velaFonte técnica: BMW — documentação técnica0.8 mm
🔧 Torques de aperto
Use ferramenta calibrada e confirme as notas específicas antes do serviço. Total encontrado: 459.
| Sistema | Componente | Torque | Rosca / quantidade | Notas | Fonte |
|---|---|---|---|---|---|
| Geral | (-) Installing topcase latch | 4,0 N·m | — | Contexto da tabela: Hold topcase latch (1) with the lug (arrow) in position and push forward.; Install release lever (1) with the lug pointing toward the recess (arrow).; Install screws (1) with washers (2) and nuts (3) with washers (4).; Topcase lock to topcase bottom | · p. PDF 912 |
| Geral | (-) Installing lock strip | 1,5 N·m | — | Contexto da tabela: Hold lock strip (3) in position and install screws (1) and (2).; Lock strip to case lid | · p. PDF 914 |
| Geral | Install screw (3). | 3,0 N·m | — | Contexto da tabela: Flashing turn indicator to number-plate carrier | · p. PDF 935 |
| Geral | Install screws (1). | 8,0 N·m | — | Contexto da tabela: Front panel carrier, left/right to front panel carrier, centre | · p. PDF 950 |
| Geral | Install screws (2). | 8,0 N·m | — | Contexto da tabela: Front panel carrier, left/right to front panel carrier, centre | · p. PDF 950 |
| Geral | Transfer holders (3) to new front panel carrier (4). | 4,0 N·m | — | Contexto da tabela: Install flashing turn indicator (2).; Install screw (1).; Flashing turn indicator to front panel carrier | · p. PDF 950 |
| Geral | Remove bolt (2). | 4,0 N·m | — | Contexto da tabela: Remove turn indicator (3).; Remount holder (4) and connector holder (5) on new front panel carrier (6).; Install turn indicator (3).; Install bolt (2).; Flashing turn indicator to front panel carrier | · p. PDF 953 |
| Geral | Lubricant | 1,5 N·m | — | Contexto da tabela: Lubricate lock barrel (2).; Lubricant; MI-Setral-43 N 83 23 2 152 082; Insert lock barrel (2) with key (1) and turn it until the locking pawl (arrow); engages.; (-) Installing lock barrel; Insert lock barrel (2) into lock strip (3), making sure that the retainer (arrow); slips over the angled face into the bore.; Install blocking ring (1).; (-) Installing lock strip; Hold lock strip (3) in position and install screws (1) and (2).; Lock strip to case lid | · p. PDF 980 |
| Geral | Remove lock strip (3). | 1,5 N·m | — | Contexto da tabela: (-) Removing lock barrel; Remove blocking ring (1).; Push the key into the lock barrel.; Press the retainer (arrow) and remove lock barrel (2) from lock strip (3).; (-) Installing lock barrel; Insert lock barrel (2) into lock strip (3), making sure that the retainer (arrow); slips over the angled face into the bore.; Install blocking ring (1).; (-) Installing lock strip; Hold lock strip (3) in position and install screws (1) and (2).; Lock strip to case lid | · p. PDF 983 |
| Geral | (-) Installing multi-controller | 0,4 N·m | — | Contexto da tabela: Position Multi-Controller (1) on grip (2), making sure that recesses (3) and; retainers (4) engage each other.; Work plug (5) for the heated grip through Multi-Controller (1).; Hold plug (5) for the heated grip in position and install screws (6), noting the; routing of the grip-heating cable (arrow).; Multi-controller to grip | · p. PDF 1035 |
| Geral | sequence: 2. | 15,0 N·m | — | Contexto da tabela: Tightening; sequence: 2. | · p. PDF 1128 |
| Geral | Insert screw (1) with washers (2) and bush (3) in right mirror (4). | 25,0 N·m | — | Contexto da tabela: Fit the original washer (5) and mirror (4) with the previously used mounting; parts.; Install bolt (1).; Mirror milled to manual controls | · p. PDF 1144 |
| Geral | Remove screw (1) and bushing (2). | 20,0 N·m | — | Contexto da tabela: Clean the threads.; Reinstall screw (1) with bushing (2) at the desired height (arrows).; Mount to carrier | · p. PDF 1162 |
| Geral | Install flat nut (1). | 2,0 N·m | — | Contexto da tabela: Position bracket (2) at the anti-twist stops (arrows) of right hand protector; (3).; Install screw (4).; Hand protector to bracket | · p. PDF 1186 |
| Geral | Install the mirror (3) and align. | 22,0 N·m | — | Contexto da tabela: Tighten the lock nut (4).; Mirror (locknut) to adapter; M10 x 1.25 Left-hand thread, | · p. PDF 1187 |
| Geral | Install mirror (3) and adjust it to the correct position. | 22,0 N·m | — | Contexto da tabela: Tighten locknut (4).; Mirror (locknut) to adapter; M10 x 1.25 Left-hand thread, | · p. PDF 1188 |
| Geral | (-) Installing the long LED turn indicator on the rear left | 3,0 N·m | — | Contexto da tabela: Feed the cable (1) with plug into position.; Position the long LED turn indicator (2) and turn to the rear.; Insert nut (4).; Install bolt (3).; Flashing turn indicator to number-plate carrier | · p. PDF 1198 |
| Geral | Remove screw (2) and nut (3). | 3,0 N·m | — | Contexto da tabela: Turn flashing turn indicator (4) up and remove.; (-) Installing the long LED flashing turn indicator on the rear right; Feed the cable (1) with plug into position.; Position the long LED turn indicator (2) and turn to the rear.; Insert nut (4).; Install bolt (3).; Flashing turn indicator to number-plate carrier | · p. PDF 1198 |
| Geral | Insert the cable into the retainer (arrow). | 3,0 N·m | — | Contexto da tabela: Installing the long LED flashing turn indicator on the rear right; Feed the cable (1) with plug into position.; Position the long LED turn indicator (2) and turn to the rear.; Insert nut (4).; Install bolt (3).; Flashing turn indicator to number-plate carrier | · p. PDF 1201 |
| Geral | Position the long LED turn indicator (2) and turn to the rear. | 3,0 N·m | — | Contexto da tabela: Insert nut (4).; Install bolt (3).; Flashing turn indicator to number-plate carrier | · p. PDF 1201 |
| Geral | Cross-member to case carrier | 19,0 N·m | — | — | · p. PDF 1204 |
| Geral | Preparatory work | 1,5 N·m | — | Contexto da tabela: + 77 44 541; Preparatory work; Open the topcase; Core activity; (-) Installing lid finisher; Requirement; Topcase lid is open.; NOTICE; If the backrest pad is to be installed along with the lid finisher, install the; backrest pad first, then the lid finisher.; Lid finisher (1) to topcase lid (2). In this process, note the locating lugs; (arrows).; Install screws (3) starting with the top right screw and then tighten in; diagonally opposite sequence.; Lid finisher to topcase lid | · p. PDF 1212 |
| Geral | OE – with HP Billet Pack (0799) | 25,0 N·m | — | Contexto da tabela: or; OE – with Option 719 Billet Pack Storm (0797); or; OE – with Option 719 Billet Pack Classic (0796); Position mirror (2) with contact discs (3) and align it.; Install bolt (1).; Mirror milled to manual controls | · p. PDF 1231 |
| Geral | (-) Installing rear left LED flashing turn indicator | 3,0 N·m | — | Contexto da tabela: Work cable (1) with the plug into the correct position.; Hold flashing turn indicator (2) in position and turn it toward the rear.; Install nut (4).; Install screw (3).; Flashing turn indicator to number-plate carrier | · p. PDF 1243 |
| Geral | Push retaining bracket (1) up. | 8,0 N·m | — | Contexto da tabela: Tighten the screws (2).; Left retainer to front panel carrier | · p. PDF 1247 |
| Geral | (-) Installing right multifunction switch | 0,4 N·m | — | Contexto da tabela: Hold the multifunction switch (4) in position.; ATTENTION; Screws overtightened past the specified value; Component damage; Install bolt (3).; Multifunction switch to grip unit | · p. PDF 1272 |
| Ignição/Elétrica | Shaft for starter idler gear to crankcase | 18,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); Shaft for starter idler gear to crankcase | · p. PDF 27 |
| Ignição/Elétrica | Oil-level sensor to gearbox cover | 8,0 N·m | — | Contexto da tabela: Thread-locking compound (mechanical); Oil-level sensor to gearbox cover | · p. PDF 29 |
| Ignição/Elétrica | Starter to gearbox cover | 12,0 N·m | — | — | · p. PDF 29 |
| Ignição/Elétrica | Wiring harness (ground) to starter | 8,0 N·m | — | — | · p. PDF 29 |
| Ignição/Elétrica | Wiring harness (positive) to starter | 8,0 N·m | — | — | · p. PDF 29 |
| Ignição/Elétrica | Clamp to silencer | 8,0 N·m | — | — | · p. PDF 34 |
| Ignição/Elétrica | Clamp to silencer and exhaust manifold | 19,0 N·m | — | — | · p. PDF 34 |
| Ignição/Elétrica | Actuator rod to ride-height sensor | 8,0 N·m | — | — | · p. PDF 38 |
| Ignição/Elétrica | Clamping screw for quick-release axle in telescopic fork | 19,0 N·m | — | — | · p. PDF 38 |
| Ignição/Elétrica | ride-height sensor to tank bracket | 5,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); ride-height sensor to tank bracket | · p. PDF 38 |
| Ignição/Elétrica | Clamping block (handlebar clamp) to fork bridge | 19,0 N·m | — | Contexto da tabela: M8 x 35 Tightening sequence: in the; forward direction of travel, tighten; until seated | · p. PDF 39 |
| Ignição/Elétrica | Retaining plate (ride-height sensor) to frame | 8,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-encapsulated); Retaining plate (ride-height sensor) to frame | · p. PDF 40 |
| Ignição/Elétrica | Sensor ring to front wheel | 5,0 N·m | — | — | · p. PDF 41 |
| Ignição/Elétrica | Micro-encapsulated | 5,0 N·m | — | Contexto da tabela: Cable holder for wheel-speed sensor to telescopic forks | · p. PDF 44 |
| Ignição/Elétrica | Tyre pressure monitoring (RDC) sensor to wheel rim | 6,0 N·m | — | — | · p. PDF 44 |
| Ignição/Elétrica | Wheel-speed sensor to fork leg | 8,0 N·m | — | — | · p. PDF 44 |
| Ignição/Elétrica | Adapter to clamping block | 25,0 N·m | — | — | · p. PDF 48 |
| Ignição/Elétrica | Ignition/steering lock to fork bridge | 19,0 N·m | — | — | · p. PDF 48 |
| Ignição/Elétrica | Battery-positive connection point to battery carrier | 2,0 N·m | — | — | · p. PDF 50 |
| Ignição/Elétrica | Operating facility for intelligent emergency call to clamp | 3,0 N·m | — | — | · p. PDF 50 |
| Ignição/Elétrica | Ride-height sensor to bracket | 5,0 N·m | — | — | · p. PDF 50 |
| Ignição/Elétrica | Wiring harness (earth) to crankcase | 8,0 N·m | — | — | · p. PDF 50 |
| Ignição/Elétrica | Wiring harness to battery | 8,0 N·m | — | — | · p. PDF 50 |
| Ignição/Elétrica | Headlight to front panel carrier | 5,0 N·m | — | — | · p. PDF 53 |
| Ignição/Elétrica | Pipe clamp with retaining plate to frame tube | 8,0 N·m | — | — | · p. PDF 56 |
| Ignição/Elétrica | Wheel-speed sensor to bevel gears | 8,0 N·m | — | — | · p. PDF 64 |
| Ignição/Elétrica | Hold positive wire (3) in position. | 8,0 N·m | — | Contexto da tabela: Install the nut (2).; Wiring harness (positive) to starter | · p. PDF 84 |
| Ignição/Elétrica | encapsulated) | 18,0 N·m | — | Contexto da tabela: Thread-locking compound (micro-; encapsulated); (-) Installing starter idler gear; Install starter idler gear (4).; Check the O-ring for damage; replace if necessary.; Install axle (3).; Install bolt (1) and sealing washer (2).; Shaft for starter idler gear to crankcase | · p. PDF 132 |
| Ignição/Elétrica | Install starter double gear (1). | 8,0 N·m | — | Contexto da tabela: Clean the threads.; Install starter double gear (1).; Check the O-ring (arrow) for damage; replace if necessary.; Install axle (2).; Install bolt (3) with sealing washer (4).; Shaft for starter double gear to crankcase | · p. PDF 132 |
| Ignição/Elétrica | (-) Installing oil-level sensor | 8,0 N·m | — | Contexto da tabela: Clean the threads.; Check O-ring (1) and renew if required.; Install oil level sensor (2) by threading through pipe (arrow).; Install screws (3).; Oil-level sensor to gearbox cover | · p. PDF 155 |
| Ignição/Elétrica | (-) Removing starter double gear | 8,0 N·m | — | Contexto da tabela: Remove bolt (1) and sealing washer (2).; Remove axle (3).; Remove starter double gear (4).; (-) Installing starter double gear; Clean the threads.; Install starter double gear (1).; Check the O-ring (arrow) for damage; replace if necessary.; Install axle (2).; Install bolt (3) with sealing washer (4).; Shaft for starter double gear to crankcase | · p. PDF 273 |
| Ignição/Elétrica | Result: | 10,0 N·m | — | Contexto da tabela: Damage like missing needles, broken housing can be detected; Measure:; Renew intermediate shaft.; Replacing intermediate shaft; Clamp sprocket (1) in a vice fitted with protective jaws.; Remove screws (2).; Remove intermediate shaft (3) from sprocket (1).; Rounded side (arrow) of sprocket (1) must face out.; Install intermediate shaft (2) in sprocket (1).; Install screws (3).; Sprocket to intermediate shaft | · p. PDF 303 |
| Ignição/Elétrica | Measure: | 14,0 N·m | — | Contexto da tabela: Oil pressure is lower than specified.; Measure:; Identify and rectify the cause of the fault.; (-) Installing oil temperature sensor; Install oil temperature sensor (2) with new sealing ring (3).; Oil temperature sensor to crankcase | · p. PDF 367 |
| Ignição/Elétrica | Oxygen sensor to exhaust manifold | 45,0 N·m | — | — | · p. PDF 379 |
| Ignição/Elétrica | (-) Installing monitoring oxygen sensor | 25,0 N·m | — | Contexto da tabela: Clean the threads.; Lubricate thread.; Install monitoring oxygen sensor (1).; Oxygen sensor after catalytic converter | · p. PDF 383 |
| Ignição/Elétrica | Equipment trim-level variant: | 14,0 N·m | — | Contexto da tabela: + 12 61 501; Equipment trim-level variant:; OE 0456 - Style HP; OE 0413 - Two-up riding package; Core activity; (-) Removing oil temperature sensor; Remove cable strap (arrow).; Disconnect connector (1) for oil-temperature sensor.; Remove oil temperature sensor (2) with sealing ring (3).; (-) Installing oil temperature sensor; Install oil temperature sensor (2) with new sealing ring (3).; Oil temperature sensor to crankcase | · p. PDF 403 |
| Ignição/Elétrica | Install the coolant temperature sensor (1) with sealing ring (2). | 15,0 N·m | — | Contexto da tabela: Coolant-temperature sensor to coolant port | · p. PDF 407 |
| Ignição/Elétrica | (-) Installing coolant hose from expansion tank | 4,0 N·m | — | Contexto da tabela: Connect coolant hose (2) and secure it in the holder (arrow).; Position clamp (1).; Connect coolant hose (2).; Position clamp (1).; Hold expansion tank (2) in position.; Install screw (1).; Expansion tank to intake air silencer | · p. PDF 496 |
| Ignição/Elétrica | (-) Installing silencer | 19,0 N·m | — | Contexto da tabela: NOTICE; To ensure the leaktightness of the exhaust system, the exhaust clamps have; to be lubricated for installation.; It is particularly important to apply lubricant to the vicinity of the joint.; Lightly lubricate the inner face of clamp (1).; Lubricant; Optimoly TA 18 21 9 062 599; Slide the clamp (1) onto the silencer (2).; Push silencer (2) to limit position.; Position washer (3), install shaped washer (4) and screw (5).; Silencer to rear frame | · p. PDF 504 |
| Ignição/Elétrica | Remount flat nut (1) on new exhaust manifold (2). | 45,0 N·m | — | Contexto da tabela: Remount left oxygen sensor (3) on new exhaust manifold (2).; Oxygen sensor to exhaust manifold | · p. PDF 506 |
| Ignição/Elétrica | Remount oxygen sensor monitor (5) on new exhaust manifold (2). | 25,0 N·m | — | Contexto da tabela: Lubricate thread, Lubricant (Optimoly; TA); Remount oxygen sensor monitor (5) on new exhaust manifold (2).; Oxygen sensor after catalytic converter | · p. PDF 506 |
| Ignição/Elétrica | Remount right oxygen sensor (4) on new exhaust manifold (2). | 45,0 N·m | — | Contexto da tabela: Lubricate thread, Lubricant (Optimoly; TA); Remount right oxygen sensor (4) on new exhaust manifold (2).; Oxygen sensor to exhaust manifold | · p. PDF 506 |
| Ignição/Elétrica | (mechanical) | 19,0 N·m | — | Contexto da tabela: Thread-locking compound; (mechanical); Install cover caps (4).; Install quick-release axle (1), to bring slider tubes (2) into alignment.; Install screws (1).; Position sensor line (2) with holder (3).; Install bolt (4).; Tighten screws (1).; Fork bridge, lower, to slider tube; M8 x 35 Tightening; sequence: Tighten; screws six times in; alternate sequence | · p. PDF 642 |
| Ignição/Elétrica | Position clamping block(1) with manual controls (2) at the marks (arrow). | 8,0 N·m | — | Contexto da tabela: Tighten the screws (3).; Handlebar fitting to handlebar; M6 x 30 Tightening; sequence: tighten; top until fully closed | · p. PDF 679 |
| Ignição/Elétrica | (-) Installing brake fitting for front wheel | 8,0 N·m | — | Contexto da tabela: Position clamping block (1) and brake fitting (2).; Install screws (3) loosely.; Position clamping block(1) with brake fitting (2) at the marks (arrow).; Tighten the screws (3).; Handlebar fitting to handlebar; M6 x 30 Tightening; sequence: tighten; top until fully closed | · p. PDF 685 |
| Ignição/Elétrica | Position operating facility (2) on handbrake fitting (3). | 3,0 N·m | — | Contexto da tabela: Install bolt (1).; Operating facility for intelligent emergency call to clamp | · p. PDF 685 |
| Ignição/Elétrica | Push front-wheel cover (2) slightly to one side. | 2,0 N·m | — | Contexto da tabela: Work the sensor cable (3) clear; (-) Replacing front wheel-speed sensor; Transfer holder (1) to female connector (2) of the new wheel-speed sensor.; (-) Installing front wheel-speed sensor; Hold wheel speed sensor (1) and brake calliper (2) in position.; Position sensor cable (3) with holder (4).; Install holder (4) with bolt (5).; Secure the sensor cable (3) in holder (6).; Push front-wheel cover (2) slightly to one side.; Work sensor cable (3) up into position.; Install bolt (1).; Front-wheel cover to telescopic forks/fork bridge | · p. PDF 848 |
| Ignição/Elétrica | Install wheel-speed sensor (2). | 8,0 N·m | — | Contexto da tabela: Install screw (1).; Wheel-speed sensor to bevel gears | · p. PDF 851 |
| Ignição/Elétrica | Working front brake line into position | 56,0 N·m | — | Contexto da tabela: Work brake line (1) with cable (2) for the wheel-speed sensor into position.; (-) Securing front spring strut; Clean the threads.; Hold spring strut (2) in position and install screw (1).; Spring strut, front, to frame | · p. PDF 888 |
| Ignição/Elétrica | Remount angular rate sensor (3) and shouldered bushings (4) on new rear- | 8,0 N·m | — | Contexto da tabela: wheel cover.; Install the nuts (1) and retaining plate (2).; Angular rate sensor to rear-wheel cover | · p. PDF 928 |
| Ignição/Elétrica | (-) Installing ring aerial | 19,0 N·m | — | Contexto da tabela: Hold ring aerial/steering-lock housing (1) in position.; Install non-removable screws (2) with special socket wrench insert (No. 51 0; 531).; Ignition/steering lock to fork bridge | · p. PDF 977 |
| Ignição/Elétrica | (-) Replacing battery | 8,0 N·m | — | Contexto da tabela: NOTICE; Installation/exchange/removal of the adapter plate may be required during; battery change.; Dispose of battery in a manner compliant with national regulations.; (-) Installing battery; Hold positive wire (4) in position.; Install bolt (3).; Wiring harness to battery | · p. PDF 1018 |
| Ignição/Elétrica | Remove the adhesive tape (arrow). | 8,0 N·m | — | Contexto da tabela: Position negative battery terminal (2).; Install bolt (1).; Wiring harness to battery | · p. PDF 1019 |
| Ignição/Elétrica | Remove bolt (1). | 3,0 N·m | — | Contexto da tabela: Remove operating facility (2) from handbrake fitting (3).; (-) Installing the operating facility for intelligent emergency call; Position operating facility (2) on handbrake fitting (3).; Install bolt (1).; Operating facility for intelligent emergency call to clamp | · p. PDF 1043 |
| Ignição/Elétrica | (-) Installing impact sensor for intelligent emergency call | 8,0 N·m | — | Contexto da tabela: Position holder (3) with impact sensor (4) on tank bracket (5).; Install bolt (1).; Holder for impact sensor to tank holder | · p. PDF 1046 |
| Ignição/Elétrica | Install bolt (2). | 6,0 N·m | — | Contexto da tabela: Holder for impact sensor to tank holder | · p. PDF 1046 |
| Ignição/Elétrica | Install angular rate sensor (3) and nuts (2). | 8,0 N·m | — | Contexto da tabela: Angular rate sensor to rear-wheel cover | · p. PDF 1058 |
| Ignição/Elétrica | Lightly lubricate the inner face of clamp (1). | 19,0 N·m | — | Contexto da tabela: Lubricant; Optimoly TA 18 21 9 062 599; Slide clamp (1) onto new silencer (2).; Push new silencer (2) to stop.; Position washer (3), install shaped washer (4) and screw (5).; Silencer to rear frame | · p. PDF 1099 |
| Ignição/Elétrica | Ensure the correct alignment of the sports silencer to cases (Arrows), | 19,0 N·m | — | Contexto da tabela: correct were needed.; Tighten screw (1) of clamp (2).; Sports silencer to rear frame | · p. PDF 1101 |
| Ignição/Elétrica | Adjusting footrest height at adjustable left front footrest | 20,0 N·m | — | Contexto da tabela: Removing carrier for footrest; Requirement; Footrest is clamped in bench vice.; Remove screws (1).; Remove clamping block (2).; Remove carrier for footrest (3).; Remove screw (1) and bushing (2).; Clean the threads.; Reinstall screw (1) with bushing (2) at the desired height (arrows).; Mount to carrier | · p. PDF 1159 |
| Ignição/Elétrica | (-) Installing step piece for footbrake lever | 10,0 N·m | — | Contexto da tabela: Remove bolt (1).; Install step piece (2) in desired bore hole and align.; Install bolt (1).; Clamping bolt for peg | · p. PDF 1164 |
| Ignição/Elétrica | Install washer (1). | 25,0 N·m | — | Contexto da tabela: Install adapter (2).; Adapter to clamping block | · p. PDF 1187 |
| Ignição/Elétrica | Position long clamping block (9) on case holder (7) from the rear and install | 8,0 N·m | — | Contexto da tabela: screws (3) in long clamping block (8) until uniformly hand-tight. Make sure; that clamping block (8) is installed through tab (arrow).; (-) Tighten adapter plate, right; NOTICE; Before tightening the adapter plate, check if the required height has been; achieved.; Fasten the adapter plate as low as possible due to the centre of gravity of the; vehicle, vehicle height and driving conditions can however require a different; position.; Align holder (1) for the adapter plate centrally to the tabs (arrows).; Tighten all the screws (2) uniformly.; Tighten adapter plate | · p. PDF 1227 |
| Ignição/Elétrica | From below, position holder (1) for LED additional headlight on front panel | 8,0 N·m | — | Contexto da tabela: carrier (2).; Install screws (3).; Bracket, LED auxiliary headlight to front panel carrier | · p. PDF 1229 |
| Ignição/Elétrica | Hold switch for LED auxiliary headlights (1) in position at clamping block (2). | 2,0 N·m | — | Contexto da tabela: Install screw (3).; Additional switch to clamping block | · p. PDF 1230 |
| Ignição/Elétrica | Remove mirror (2). | 8,0 N·m | — | Contexto da tabela: Remove washers (3) .; Removing clamping block; Remove screws (1).; Remove clamping block (2) from handlebar fitting (3).; Installing clamping block for handlebar fitting for clutch; Hold clamping block (1) in position at handlebar fitting (2).; Loosely install screws (3).; Position handlebar fitting (2) at the marks (arrow).; Tighten screws (3).; Handlebar fitting to handlebar; M6 x 30 Tightening; sequence: tighten; top until fully closed | · p. PDF 1230 |
| Ignição/Elétrica | Care products | 5,0 N·m | — | Contexto da tabela: Lubricate rubber grommets (1) slightly.; Care products; Rubber care product 83 12 0 397 018; Install headlight (2).; Pay attention to the correct seating of rubber grommets (1) in holder (arrow).; Install contact disc (1) and hold.; Push headlight (2) down slightly.; Install retaining clip (3) with suitable pliers.; Connect connector (1) for the headlight.; Install screws (1) and contact discs (2).; Headlight to front panel carrier | · p. PDF 1236 |
| Ignição/Elétrica | Centre headlight guard (1). | 2,0 N·m | — | Contexto da tabela: Tighten screws (1) of the brackets.; Bracket to cockpit fairing | · p. PDF 1240 |
| Ignição/Elétrica | Install screws (2), counter-holding in each case at hexagon (3). | 2,5 N·m | — | Contexto da tabela: Spacer studs to headlight guard | · p. PDF 1240 |
| Ignição/Elétrica | (-) Securing front wheel-speed sensor | 8,0 N·m | — | Contexto da tabela: Check the O-ring (1) for damage, replace if necessary.; Hold wheel speed sensor (2) in position.; Install bolt (3).; Wheel-speed sensor to bevel gears | · p. PDF 1259 |
| Motor | Bracket, engine guard to crankcase | 19,0 N·m | — | — | · p. PDF 26 |
| Motor | Camshaft bearing cap to cylinder head | 10,0 N·m | — | Contexto da tabela: M6 x 35 Tightening sequence: tighten; alternately | · p. PDF 26 |
| Motor | Cylinder head to crankcase | 5,0 N·m | — | Contexto da tabela: M10 x 110 - 10.9 Tightening sequence: tighten in; diagonally opposite sequence | · p. PDF 26 |
| Motor | Diaphragm valve to crankcase | 12,0 N·m | — | — | · p. PDF 26 |
❓ Perguntas frequentes
As respostas abaixo são montadas somente com dados publicados nesta ficha.
Quantos litros de óleo vão na BMW R 1250 GS K50 2019 a 2022?
A ficha técnica indica: 4 L com troca do filtro.
Qual é a taxa de compressão da BMW R 1250 GS K50 2019 a 2022?
A ficha técnica indica: 12.5:1.
Qual é a folga das válvulas da BMW R 1250 GS K50 2019 a 2022?
A ficha técnica indica: admissão: 0.10...0.17 mm; escape: 0.34...0.41 mm.
Qual é a calibragem dos pneus da BMW R 1250 GS K50 2019 a 2022?
A ficha técnica indica: dianteiro: 2.5 bar; traseiro: 2.9 bar.
Qual é a capacidade do tanque da BMW R 1250 GS K50 2019 a 2022?
A ficha técnica indica: 20 L.
Quais são o diâmetro e o curso do motor da BMW R 1250 GS K50 2019 a 2022?
A ficha técnica indica: 102.5 mm × 76 mm.
Qual é o torque de Coolant filler adapter in crankcase na BMW R 1250 GS K50 2019 a 2022?
5,0 N·m.
Qual é o torque de Radiator to frame na BMW R 1250 GS K50 2019 a 2022?
8,0 N·m.